4
ENGLISH
•
From time to time check the power cord
and the power plug integrity.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a mainte-
nance service or similar qualified person-
nel to avoid danger.
•
Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any
malfunction is detected or after it was
dropped, unplug the unit and apply to any
authorized service center from the con-
tact address list given in the warranty cer-
tificate and on the website www.vitek.ru.
•
Transport the unit in the original package
only.
•
Keep the unit out of reach of children and
disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USE ONLY, ITS COMMERCIAL USAGE AND
USAGE IN PRODUCTION AREAS AND WORK
SPACES IS PROHIBITED.
USING THE HAIRDRYER
After unit transportation or storage at low
temperature it is necessary to keep it for
at least two hours at room temperature
before switching on.
•
Unpack the hairdryer and remove any
stickers that can prevent unit operation.
•
Unwind the power cord completely.
•
Before switching the unit on, make sure
that your home mains voltage corresponds
to the unit operating voltage.
•
Insert the power plug into the mains socket.
Switching hair dryer on
Before switching the appliance on make sure
power supply voltage meets operating volt-
age of the appliance.
• Insert power cord plug into wall outlet.
• Select operating speed you need using air-
flow speed switch (1):
0 = switched off;
I = low speed;
II = high speed.
• Select airflow temperature you need using
heating degree switch (2).
I = slight heating
II = medium heating
III = maximal heating
Taking care about your hair
Before drying and setting your hair, wash them
with shampoo, dry with towel to remove ex-
cessive moisture and brush for better results.
Fast drying
Set switch (2) into position of maximal heat-
ing (position III), select airflow speed you
need using switch (1) and dry your hair out
a little bit. Shake off excessive moisture by
hand or using a brush and continuously move
the hair dryer over your hair.
Straightening your hair
Set switch (2) into position of maximal heat-
ing (position III), select airflow speed you
need using switch (1) and dry your hair out
a little bit. When your hair are almost dry, in-
stall concentrating nozzle (6), reduce degree
of air heating by switch (2) and airflow speed
by switch (1).
Divide your hair into locks and layers and start
straightening from the lower layers. Using a
plain or a round comb, brush the hair down-
wards and simultaneously direct hot air from
the nozzle (6) at your hair. This way, slowly
straighten each lock from root to end. After
you finish straightening the locks of the lower
hair layer, start straightening the locks of the
middle layer and finish with the locks of the
upper hair layer.
Natural waving structure of your hair
Set switch (2) into position of slight heating
(position I), then set switch (1) into position I,
hold a lock between your fingers tightly, turn
it to direction of its natural curliness, then dry
the lock out by directing air jet between the fin-
gers. After getting the shape you need, press
cool shot button (3) « » and fix each lock.
Volume styling
Using hair dryer in any mode of heating/
any speed from slight to maximal, dry out
hair roots beginning from backside of your
head.
Styling your hair
Set the switches (1, 2) to the low heating/
speed position and install the nozzle (6) on
the hairdryer to direct the air flow.
IM VT-2533.indd 4
10/24/19 11:58 AM
Summary of Contents for VT-2533
