Vitek VT-2330 B, Manual Instruction

Page: 5 / 24

5
ENGLISH
dry, switch the unit off, set the nozzle (4),
decrease the heating degree using the switch
(2) and set the required air flow speed using
the switch.
Divide your hair into locks, start straightening
from the lower layers. Using a plain or a round
brush, brush the hair downwards and simul-
taneously direct hot air from the nozzle (4) at
your hair. This way, slowly straighten each lock
from root to end. After you finish straightening
the lower locks, start straightening the locks of
the middle layer and finish with the locks of the
upper hair layer.
Natural wavy hairstyle
Set the switch (2) to the low heating position « »;
select the low air supply speed by setting the
switch into position « ». Grip locks between
fingers tightly, turn them in the direction of
natural curling. Dry your hair, directing the air-
flow between fingers. When the required effect
is achieved, press and hold down the cool shot
button (3)
and fix each lock.
Styling
Attach the nozzle (4) to the hairdryer and then
set the switches (1, 2) to the low heating/low
speed positions « »/« ».
Divide your hair into locks and create a required
hair style by means of a round hair-styling
brush. During hair styling, direct the air flow
straight at your hair.
If you want to fix the hairstyle, direct the cool
air flow at each lock for 2-5 seconds. Styling
time is determined individually according to
hair type; you can adjust it by yourself.
Oil dispersion function
Use cosmetic oil for hair care. Hot air flow
passes through the sponge (10) and speeds
up the evaporation, oil particles accumulate on
the hair and provide additional hair care dur-
ing styling.
Attention!
To avoid getting of oil into the unit, first
remove the dispenser (8) from the unit
body and soak the sponge (10) in a small
amount of oil (no more than 2-3 drops).
–
Make sure that the unit is unplugged.
–
If the dispenser (8) is installed on the unit
body, remove the dispenser (8).
–
Remove the lid (9) rotating it clockwise.
–
Add 2-3 drops of oil on the sponge (10).
–
Place the ledges of the lid (9) into the
grooves on the dispenser (8) and rotate the
lid counterclockwise until it is fixed.
–
Place the dispenser (8) on the unit body.
–
Install the nozzle (4).
Overheating protection
Overheating protection switches the hairdryer
off if the outgoing air is too hot. If the hairdryer
has been switched off during operation, set
the switch to the «0» position, unplug the hair-
dryer and make sure that the inlets and outlets
are unblocked. Let the hairdryer cool down for
5-10 minutes and switch it on again. Do not
block the air inlets during unit operation and
avoid getting of hair into its air inlet.
CLEANING AND CARE
The hair dryer is intended for household usage
only.
1.
Set the switch to the «0» position and dis-
connect the hairdryer from the mains.
2.
Clean the unit body with a damp cloth and
then wipe it dry.
3.
Never immerse the unit into water or other
liquids.
4.
Do not use abrasives and solvents to clean
the unit body.
STORAGE
–
Always unplug the hairdryer if you are not
using it.
–
Let the unit cool down after use and keep
it in a dry cool place out of reach of chil-
dren.
–
Never wind the cord around the hairdryer,
as it can damage the unit. Handle the power
cord with care, do not pull, twist or stretch
it, especially near the power plug or at the
junction point. Straighten the cord periodi-
cally if it gets twisted during hairdryer oper-
ation.
–
For easy storing there is a hanging loop (7),
you can hang the unit on this loop provided
that no water gets on the unit in this position.
VT-2330.indd 5 25.07.2014 9:54:22