Vitek VT-1770 W Manual Instruction Download

Page: 5 / 52

ENGLISH

•

Always  unplug  the  unit  and  pour  out  water
from  the  water  tank  and  disc  filter  block
before  cleaning  or  if  you  do  not  use  the
humidifier.

•

Before moving the humidifier to another
place, unplug it and pour out water from the
water tank and disc filter block. When moving
the unit, hold it by the base with both hands.

•

Do not touch the power plug with wet hands.

•

Before using the unit, closely examine the
power cord and make sure that it is not dam-
aged. Do not use the unit if the power cord is
damaged.

•

Do not switch on and do not use the unit if the
cord or the plug is damaged or if the fan heat-
er works irregularly, fell or is damaged. In this
case contact an authorized service center for
testing and repair

•

Do not dismantle the unit by yourself, if any
malfunction is detected, apply to the nearest
authorized service center.

•

Clean the unit regularly.

•

Keep the unit out of reach of children.

THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY

BEFORE THE FIRST USE

After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.

–

Unpack the unit and remove any stickers and
package materials that can prevent unit oper-
ation. Examine the unit for damages. In case
of damages do not switch the unit on.

Notes:

–

Use the humidifier at the room tempera-
ture from +5° С to +40° С and relative
humidity less than 80%.

–

Water temperature should not exceed
+40°С.

–

Before connecting the humidifier to the mains
make sure that your home mains voltage cor-
responds to unit operating voltage.

OPERATION

This unit type humidifies and cleans air by blow-
ing hot air on the wet disc filter, thereby dust
particles accumulate in water and on filter discs.

–

Remove the lid (4) moving it aside.

–

Take the water tank (6) by the handle (7) and
remove it from the unit body (pic. 1).

–

Turn over the tank (6), open the lid (5) rotat-
ing it counterclockwise. Fill the tank (6) with
necessary amount of water, close the lid (5)
rotating it clockwise (pic. 2).

–

Put the filled water tank (6) back to its place
and close the lid (4). Wait for some time, that
is necessary to fill the disc filter block (1) with
water.

–

Insert the plug into the socket, you will hear
a sound signal.

–

Switch the unit on by pressing the «ON/OFF»
button  (17).  You‘ll  hear  a  sound  signal,  the
standard  operation  mode  indicator  (12)  and
the  relative  room  air  humidity  indicator  (9)
will light up.

–

After the unit operation switch the unit off by
pressing the «ON/OFF» button (17).

–

Wait till the unit switches off completely (the
fan motor stops in approximately 30 sec-
onds) and then unplug the unit.

Notes:

–

Every pressing of the buttons is con-
firmed with a short sound signal.

–

The humidity level shown by the indicator
(9) may be different from the readings of
another hygrometer.

–

The humidity level indications depend on
the room temperature.

–

Draughts or other air flows may affect the
air humidity indications in the room.

CONTROL PANEL (8)
«ON/OFF» button (17)

To switch the unit on, press the «ON/OFF» but-
ton  (17)  once.  Switch  the  unit  off  by  pressing
the «ON/OFF» button (17) again, the indicators
on  the  control  panel  (8)  will  go  out,  and  the
unit  will  be  switched  off  in  approximately  30
seconds.

«MODE» button (11)

Select the operating mode pressing consequent-
ly the «MODE» button (11), one of the indicators
(12) will light up:

–

Standard

* - operation mode maintaining the

relative room humidity 50%;

–

Humidification

* - operation mode maintain-

ing the relative room humidity 60%;

–

Sleep