Ultra-Aire SD12 Installation Instructions Manual Download | Manualshive

Page: 1 / 36

background image

TS-712 5/18 Rev D

P/N: 4033170 Serial No.:

Install Date:

Sold by:

HVAC Installer: Please Leave Manual for Homeowner

The Ultra-Aire SD12 is a split system dehumidifier with sensible cooling
that is integrated into the heating and cooling system to provide the
ultimate in comfort, health and property protection through:

• Dehumidification
• Sensible Cooling
• Fresh Air Ventilation (Optional)
• Air Filtration

The two-piece design allows the sensible heat load generated from
dehumidifying the house to be released in the outside condensing unit,
thus eliminating additional cooling and reducing air conditioner run time.

Installation Instructions

INSTALLATION BY A HVAC PROFESSIONAL IS RECOMMENDED

YEAR

FULL WARRANTY

YEAR

FULL WARRANTY

1
2
3
...
»

Summary of Contents for SD12





































Reviews:

No comments

Related manuals for SD12

Brand: Quest Engineering Pages: 6

Brand: Quest Engineering Pages: 26

Airtek SMART CYCLE PLUS 100

Brand: Parker Pages: 45

Brand: Bionaire Pages: 10

Brand: stockli Pages: 60

Brand: iGenix Pages: 5

Brand: Dantherm Pages: 15

Brand: madebyzen Pages: 11

Brand: ECG Pages: 120

Brand: Eberg Pages: 62

Brand: Sullair Pages: 84

Brand: Timberk Pages: 48

Brand: Elechomes Pages: 24

Brand: Stanley Pages: 24

Brand: KDK Pages: 26

Brand: Walton Pages: 6

Brand: Calorex Pages: 72

Brand: HANKISON Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands