7
ENGLISH
Make at least a 10-20 minute break before
switching the mixer on again.
The blender is intended for chopping products,
mixing different ingredients or making cocktails.
–
Place the mixer vertically on a flat, dry and
steady surface.
–
Turn the protective lid (3) counterclockwise
and remove it.
–
Match the mark «
▼
» on the knife block (13a)
with the mark on the mixer body «
▲
» and
turn the blender bowl (13) clockwise as far
as it will go.
–
Remove the blender bowl (13) lid and put
the necessary ingredients into the bowl (13).
–
Close the blender bowl (13) with the lid.
Notes:
–
Before starting to chop/mix, we recom-
mend to peel fruit, remove inedible parts,
such as stones, and cut fruit into cubes
approximately 2х2 cm in size.
–
The blender is not intended for beat-
ing eggs, making potato mash, kneading
dough, extracting fruit or vegetable juice,
chopping hard or frozen products, chopping
meat and meat products.
–
The amount of the processed products should
not exceed 2/3 of the bowl (13) capacity.
–
Insert the power plug into the socket.
Note: – the blender will not be switched on if
the blender bowl (13) is installed incorrectly.
–
Use the operation mode switch (5) to set the
required speed of knives rotation:
«0» the blender is off
«1-2-3» – for mixing liquid products.
«4-5»– for liquid and hard products.
–
During the breaks between the operation
cycles, you can add the required ingredients
into the bowl (13). To do this, remove the
blender bowl (13) lid and add the required
ingredients, close the lid.
–
After the unit operation is finished, set the
operation mode switch (5) to the «0» posi-
tion and unplug the unit.
–
Remove the blender bowl (13), for this rotate
it counterclockwise.
–
Remove the lid from the bowl (13) and take
the products out.
–
After the operation is finished, wash the
blender bowl (13).
Note: - if food processing is hindered, you can
add some water, liquor or juice into the blender
bowl (13).
–
Install the protective lid (3) back to its place
and turn it clockwise until the mark «
▼
» on
the lid (3) matches the mark «
▲
» on the
mixer body.
Note: – the mixer will not be switched on if the
lid (3) is installed incorrectly.
USING THE CHOPPER
When chopping products in the chopper
bowl the operation time should not exceed
30 seconds. Make at least a 5-10 minute
break before switching the mixer on again.
The chopper is used to chop meat, cheese,
onion, herbs, garlic, carrots, walnuts, almonds,
prunes, vegetables and fruit.
ATTENTION!
Do not chop very hard products, such as ice
cubes, frozen products, nutmegs, coffee
beans, cereals etc.
Before you start chopping:
–
Cut meat, cheese, onions, vegetables or fruit
into pieces approximately 2x2 cm in size.
–
Remove stems of herbs, shell nuts.
–
Remove bones, sinews and cartilage from
meat.
Chopping
Warning: the blades of the chopping knife
(18) are very sharp! Always hold the chopping
knife (18) by the plastic end.
–
Place the chopper bowl (17) on a dry, flat
and steady surface.
–
Set the chopping knife (18) on the axis in the
chopper bowl (17) by holding on the plas-
tic end.
–
Put the products into the chopper bowl (17).
Note: - do not switch the unit on when the
chopper bowl (17) is empty.
–
Place the lid (16) on the chopper bowl (17)
and rotate it clockwise as far as it will go “ ”.
–
Open the blender attachment installation
place (7) lid, install the mixer on the lid (16)
and turn it counterclockwise as far as it will
go “ ”. Make sure that the mixer is fixed
properly.
–
To switch the unit on, press and hold down
the pulse mode button «P» (6).
–
During the unit operation hold the mixer with
one hand and the chopper bowl (17) with the
other hand.
IM VT-1430.indd 7
13.12.2018 15:37:35