5. PROGRAMMING
D-304762 PowerMaster-10/30 G2 Installer's Guide
59
Enter the "
WL DEVICES
" menu, select the type of test you wish to perform (see guidance above and in section 5.9.1),
then refer to the table below which provides you with detailed explanations for each option.
Option
Instructions
TEST ALL DEVICES
You can test all devices automatically, one after the other.
While in "
TEST ALL DEVICES
", press
to initiate the test.
The devices are tested in the following order: wall-mounted devices, keyfobs and handheld
devices.
At the end of the test process, the panel will present the following: "
SHOW ALL DEVICES
".
Press
to view devices' status.
Note:
Refer to "
SHOW ALL DEVICES
" section below for further information on device status.
Pressing any key during the testing process will open the following options:
1. Press
to jump to the next device group. For example, from wall-mounted devices to
keyfobs.
2. Press
to continue the testing process
3. Press
to exit the test process.
While in the handheld devices test process, indicated by the corresponding display, for
example, "
TEST KEYFOBS 01
", press any key of the selected device to initiate the test.
TEST ONE DEVICE
→
→
→
→
CONTACT SENSORS
→
→
→
→
MOTION SENSORS
→
→
→
→
GLASSBREAK SENS.
You can select a specific device group you wish to test, for example, Motion Sensors.
Press
to enter the "
TEST ONE DEVICE
" sub menu and use
to scroll through the
device families. Press
to enter the
<device family>
sub menu, for example:
"
MOTION SENSORS
".
The following screens will appear: "
Xxx:<device name>
"
"<
location
>"
Where Xxx indicates the device number.
If there is no device, the following screen will appear: "
NO EXISTING DEV.
".
Press
to test the selected device. The following screen will appear: "
TESTING Zxx NNN
".
While in the handheld devices test process, indicated by the corresponding display, for
example, "
TEST KEYFOBS 01
", press any key of the selected handheld device to initiate
the test.
At the end of the test process, the panel will present the devices' status: "
Zxx:
24hr: <status>
"
1
"
Zxx: NOW: <status>
"
1
.
Note:
Refer to "
SHOW ALL DEVICES
" section for further information on device status.
SHOW ALL DEVICES
You can view the devices status.
Note:
This option is available only after testing process was done.
Press
to view the devices' status.
The following screens will appear: "
Zxx: 24hr: <status>
"
1
"
Zxx: NOW: <status>
"
1
Use
to scroll between the device's families.
SHOW RF PROBLEMS
You can view only the devices which have RF problems.
Note:
This option is available only after testing process was done.
Press
to view the devices' status.
The following screens will appear: "
Zxx: 24hr: <status>
"
1
"
Zxx: NOW: <status>
"
1
Use
to scroll between the device's families.
5.9.3 Testing the GSM module
The PowerMaster enable to test the GSM module integrated inside the panel.
07:DIAGNOSTICS
⋅ ⋅ ⋅
GSM/GPRS
1
The signal strength indications are as follows: "
STRONG
";
GOOD
"; "
POOR
"; "
1-WAY
" (the device operates in 1-way
mode or, the "
NOW
" communication test failed); "
NOT TST
" (results are shown without any performed test); "
NOT
NET
" [device is not networked (not fully enrolled)]; "
NONE
" (keyfob 24Hr result); or "
EARLY
" (result of the last 24Hrs
without statistics).
