Vislink AJ-RC10 User Manual Download Page 48 | Manualshive

Page: 48 / 70

background image

User Manual Focal Point

Data Receiver

Issue No: M

Page: 40

Ref: FOCL-ASUM-8xxx

Copyright © 2017 Vislink plc

Connector

6-Pin, 1-Key LEMO Socket

Pin

Signal

1

Red Tally Signal

2

12V Prot

3

Green Tally Signal

4

TTL TX (TTL CC Hitachi)

5

TTL RX (TTL CC Hitachi)

6

GND

Figure 5-5

Standalone Data Receiver Overview

The Standalone Data Receiver Version07 Unit is small/discrete and easy to mount on many
camera types.

The data connector allows remote connectivity to various camera manufactures and
models using the correct data cable.

The FocalPoint Camera Control system offers control to various camera manufactures and
models using one-way data with the Vislink OCP5 and one-way or return data using any of
the following:



Sony RCP 750/1500/1530



Hitachi RU1500



Panasonic AJRC10G.



Ikegami OCP300/399/100



Panasonic AW-RP50E, AW-HE120G



Grass Valley OCP400

When using the Return Data option, you need to connect the RTN DATA to the User Data
input of the MVL Transmitter.

The DR07 is controlled via a Windows™ PC GUI using TelemetryReceiverInterface.exe. The
Telemetry Receiver Interface user guide is supplied with the GUI when installed.

The configuration cable from the PC connects to a 5-Pin BINDER socket, labelled CONFIG.

«
...
46
47
48
49
50
...
»

Summary of Contents for AJ-RC10







































































Reviews:

No comments

Related manuals for AJ-RC10

Brand: GE Pages: 425

Brand: Hankscraft Runxin Pages: 53

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Brand: Samson Pages: 20

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

Brand: Newport Pages: 417

TVNext NN01-054

Brand: Fractus Antennas Pages: 14

Brand: KanDao Pages: 265

Brand: Frico Pages: 12

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brand: Greenheck Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands