Vislink AJ-RC10 User Manual Download Page 44

Page: 44 / 70

User Manual Focal Point

Data Receiver

Issue No: M

Page: 36

Ref: FOCL-ASUM-8xxx

Function

Range

RF Input

SMA Type socket located on top edge panel -
direct mounting Receive antenna whip.

RF Min Sensitivity

0.5uV

Available Frequency Bands

430-470 MHz (Standard)

450-490 MHz

Channel Spacing

6.25 KHz (Standard)

12.50 KHz

Figure 5-2

InCam-G Overview

The InCam-G unit is a fully integrated dockable Camera Back for the Grass Valley LDX
camera.

The unit has a built-in MVL Transmitter that sends video and audio generated by the LDX
camera to a Receive point.

The unit also has a built-in telemetry Data receiver.

The FocalPoint Camera Control system offers remote control operation/functionality to the
camera using one-way data from the Vislink OCP5 controller.

NOTE: Return data is available to the OCP5 if the user data out from the MVL Receiver is

connected directly to the OCP5 @ 115200 baud.

You can control the camera from a PC with Windows™ OS installed, using the Vislink
software IncamProgrammer.exe. User instructions are available from the user guide,
which is accessed from the GUI.

The configuration cable from the computer connects to the Config 4-Pin BINDER socket.

The LDX camera on/off switch is the master power for the camera and the InCam-G.

The InCam-G has an isolated power switch after the camera is powered:



Off

Camera operates with the InCam-G powered off.



Standby

InCam is configurable but not Transmitting or Receiving.



Camera and InCam are powered.

Summary of Contents for AJ-RC10





























































Search results

Summary of Contents for AJ-RC10

Reviews:

Related manuals for AJ-RC10

Brands by name

Popular brands

Vislink AJ-RC10, User Manual

Search results

Summary of Contents for AJ-RC10

Reviews:

Related manuals for AJ-RC10

Brands by name

Popular brands