Vislink AJ-RC10 User Manual Download Page 12 | Manualshive

Page: 12 / 70

background image

User Manual Focal Point

General Information

Issue No: M

Page: 4

Ref: FOCL-ASUM-8xxx

Copyright © 2017 Vislink plc

The FocalPoint system complies with Part 15 of the FCC Rules (Code of Federal Regulations
47CFR Part 15). Operation is subject to the following two conditions: (1) This device does
not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Part 15 The FocalPoint system has been type accepted for operation by the FCC in
accordance with Part 90 of the FCC rules (47CFR Part 90).

Part 90 The FocalPoint has been type accepted for operation by the FCC in accordance with
Part 101 of the FCC rules (47CFR Part 101). See the label on the unit for the specific FCC ID
and any other certification designations.

Part 101 Industry Canada This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.

ICES-003 The FocalPoint system has been certified for operation by Industry Canada in
accordance with RSS-119 and RSS-210 of the Industry Canada rules. See the label on the
unit for the specific Industry Canada certification number and any other certification
designations.

RSS-119 Changes or modifications not expressly approved by Vislink could void the user’s
authority to operate this equipment. Notice Shielded cable must be used with this
equipment in order to ensure that it meets the emissions limits for which it was designed.
It is the responsibility of the user to obtain and use good quality shielded cables with this
device.

WARNING: DO NOT operate radio equipment near electrical blasting caps or in an

explosive atmosphere.

WARNING: DO NOT operate any radio transmitter unless all RF connectors are secure and

any open connectors are properly terminated.

WARNING: DO NOT allow the antenna to come close to, or touch, the eyes, face, or any

exposed body parts while the radio is transmitting. In order to ensure the safe
operation of this radio equipment, the minimum distance that a person should
be from the attached antenna when this equipment is transmitting is 5.5 ft.
(165 cm). This is based on using the FocalPoint system at a power of 5 watts
with a 10dBd (12.1dbi) gain antenna.

«
...
10
11
12
13
14
...
»

Summary of Contents for AJ-RC10







































































Reviews:

No comments

Related manuals for AJ-RC10

Univerge SV8100

Brand: NEC Pages: 2

Brand: Zolix Instruments Pages: 22

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: S&P Pages: 12

Brand: S&C Pages: 34

Brand: S&C Pages: 32

IntelliCap Plus

Brand: S&C Pages: 32

Brand: S&P Pages: 12

Brand: S&C Pages: 35

Brand: TANDBERG Pages: 2

6000 MXP Profile

Brand: TANDBERG Pages: 2

3000 MXP Profile

Brand: TANDBERG Pages: 2

Brand: TANDBERG Pages: 11

Media Processing System MPS 800

Brand: TANDBERG Pages: 106

Brand: TANDBERG Pages: 44

Brand: TANDBERG Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands