Vision & Control Vicosys 5400 Instructions For Use Manual Download Page 21

Page: 21 / 64

vicosys

5400

Technical Data

999.994.729.10-en-2.3

5.3 Interfaces

5.3.1 Ethernet interfaces

The device has two Ethernet interfaces:

DVI

LAN 2

USB

CAN 2

CAN 1 / Serial 2

LED

CAN 1

CAN 2

LED

- R

Serial 1

LAN 1

CFAST

HD PWR

RST PWR

I/O

Image 6: Ethernet interfaces

(1)

LAN 1

(2)

LAN 2

Characteristics

•

Ethernet interfaces 1 (LAN 1): Integration of the device in a LAN, suitable

for process communication as well as parametrisation with the operating

software vcwin pro.

•

Ethernet interfaces 2 (LAN 2): Direct connection to a PC running the

operating software vcwin pro (service connection).

•

LAN: 10/100/1000 Mbps

Configuration

The device supports auto MDI-X. To integrate the device in a network a patch

cable or crossover cable can be used.

Summary of Contents for Vicosys 5400

































































Search results

Summary of Contents for Vicosys 5400

Reviews:

Related manuals for Vicosys 5400

Brands by name

Popular brands

Vision & Control Vicosys 5400, Instructions For Use Manual

Search results

Summary of Contents for Vicosys 5400

Reviews:

Related manuals for Vicosys 5400

Brands by name

Popular brands