ENGLISH
EN
15
•
START:
Press the “START” button and the treadmill will start
after three seconds at 1 km/h.
•
+/-:
Press the “+” button to increase the speed and the “-” button
to decrease the speed. The minimum speed is 1 km/h and the
maximum speed is 12 km/h.
•
MODE:
Press the “MODE” button and the display shows “SPEED”,
“TIME” and “CALORIES”. The display lights up every five seconds
with the data “SPEED”, “TIME” and “CALORIES”.
Functions
•
PROGRAM:
Press this button to select a program in manual
mode: P1 --- P15 ---- “FAT”.
•
MODE:
When the treadmill is ready, press this button to select
the mode: time mode countdown, distance mode countdown,
calorie mode countdown.
•
START:
Press this button to start the treadmill, after three
seconds the treadmill will start at the lowest speed or standard
program speed.
•
STOP:
Press this button to stop the treadmill. The treadmill will
stop slowly.
•
SPEED ↑/↓:
Sets the speed. Press this button to adjust the
speed during your workout.
•
SPEED (3-6-9-12):
Adjusts the speed in rapid increments.
•
HANDLE BUTTON (R):
Speed knob.
•
HANDLE BUTTON (L):
START/STOP button.
•
HEART RATE TEST:
The heart rate will appear on the display
after five seconds if the handle is held with both hands. To
measure heart rate more accurately, please perform the test
when the treadmill stops, then hold the handles for more than
30 seconds. The heart rate displayed may differ from the actual
heart rate.
PROGRAMS (FIG. 07)
The treadmill has 12 programs P1-P12. Press “PROG” when the unit is
in standby mode to set the programs and press “START” to turn the
treadmill on. After turning the treadmill on, press the “PROG” button
directly or press “STOP” twice and the treadmill will display “OFF” and
go into sleep mode to view all programs. The programs are shown on
page 9. The horizontal line represents time, and each dot represents
a minute and a half. The vertical line represents speed and each dot
represents 1 km/h. Each program lasts 30 minutes.
ERROR CODES
E01:
Console signal failed.
•
Solution:
Check that the sensor cable is not damaged and that
it is correctly connected. If it is, replace the console.
E02:
The console does not recognise the engine power.
•
Solution:
: Check that the positive and negative motor cables
are correctly connected to the console terminal interface. If this
is correct, check that the power tube (located on the console and
peripherals) is not damaged. If this does not correct the problem,
replace the console or motor.
E03:
The speed display is not recognised by the console when the
motor is running.
•
Solution:
Verify that the motor is running when the treadmill
is turned on and that error code “E03” is displayed. Check that
the light sensor is working properly. Check that the light sensor
cable is secure and that the junction between the light sensor
and the four white pins on the console are properly connected. If
all of the above are correct, check the area of the four white
pins on the peripheral unit for damage and consider replacing
the console and circuit board. If the motor does not work when
error code “E03” is displayed, check if the motor is broken and
consider replacing it.
E05:
When the motor is running, the voltage is higher than the
protection value.
•
Solution:
Check that the motor is in good condition and that
nothing is trapped between the rotating shoe and the motor,
which increases the resistance. If all of the above is correct,
replace the console.
E07:
The signal from the safety key is not recognised by the computer,
so the display shows E07 or “--- ---”.
•
Solution:
Check that the magnetic parts of the security key are
securely attached.
CONSOLE (FIG. 06)
