manualshive.com logo in svg

virtual access GW8600 Service Managed Gateway, Installing And Configuring

Share
Download
virtual access GW8600 Service Managed Gateway Installing And Configuring Download Page 5

 

2: Physically installing the GW8600 SMG 

Installing and Configuring the GW8600 SMG 

© Virtual Access Ltd. 

Issue 1.1 

Page 5 of 12 

 

2.1.3

 

Protect unused access points 

Cover unused access points with blanking plates.  

2.2

 

Unpacking the GW8600 SMG 

Remove the GW8600 SMG and parts from the packaging. Check the parts against the 
packing list that is inside the packaging. 

Figure 2 shows the components of the GW8600 SMG. 

 

Figure 2: The components of the GW8600 SMG 

2.3

 

Assessing the GMS/GPRS signal strength at the installation 
location 

Before you install or mount the GW8600 SMG, ensure the GMS/GPRS signal is adequate 
at the installation location.  

The 7-segment display on the upper right-hand corner of the WebWay 2424B 
Communicator indicates the signal strength in a range 0–9. 0 is the weakest signal and 9 
is the strongest signal. 

Summary of Contents for GW8600 Service Managed Gateway













Reviews:

No comments

Brands by name

Popular brands

Load more brands