background image

5

VIR

O

 TECH

 MINI

 -

 USER

 M

ANU

AL

SETUP

IDEAL PLACEMENT

There are several important factors to consider when selecting a location for your air purifier:
•  Make sure the location you choose is as far away from the HVAC air return duct as possible. This will ensure that the 

purification produced by the air purifier is optimally circulated.

•  Place the unit on top of something tall such as a bookcase, a shelf or a mounting bracket, leaving only 30 to 60 cm 

between the unit and the ceiling. Point the unit towards the centre of the room.

•  To ensure the unit works properly, there should be as much space as possible in front of your air purifier so that it can 

efficiently process the air in the area.

•  Never place an operating unit on the floor.
•  Nearest the source of the worst pollution.

INITIAL SETTING

Before using the unit you will need to find the area (or square metres) of the environment. To do this accurately, take into 
account all connected rooms with open doorways (the purification does not flow readily through closed doors).
The Air purifier can purify up to 279 m

2

 of space.

For example: Suppose you have a 232 m

2

 house. The living room is attached to the kitchen, three bedrooms, the den and a 

laundry room. The kitchen and three bedrooms’ doors remain open the majority of the time but the laundry room and den 
usually remain closed off from the rest of the house. Together, the laundry room and den have a combined area of 46 m

2

The area of the environment you would want to set your air purifier and purify would be 186 m

2

.

Once you have determined an ideal location for your unit and calculated the area of the environment:
1.  Connect the Power Cord into the unit.
2.  Insert the Power Plug into the wall outlet.
3.  Turn the unit on and set it to “NORMAL” mode (see “OPERATIONS”: page 7).
4.  Leave the unit on “NORMAL” mode for at least 24 hours to begin with.
5.  After 9 hours, set the unit to “HIGH” mode and set the square metres to 24 m

2

.

6.  Gradually increase the square metres setting every 24 hours until you reach the accurate square metres of your area 

which you calculated in the initial steps).  

NOTE

Using the purifier at a setting less than the m

2

 of the area being treated is acceptable and may be desirable in an environment 

relatively free of pollutants.

Register your product for 12 month warranty at:

https://f-tech-warranty.com

Summary of Contents for MINI















Reviews: