Vira 162140 Instruction Manual Download Page 13

Page: 13 / 68

General description of the 162140 threading machine

Basic functions

The 162140 threading machine carries out the following three functions:

cutting tubes
threading tubes by stock removal
reaming

Diameters of tubes which can be threaded

Depending on the tube diameter, the threads are cut using one of the two self opening die heads

tube diameter, the threads are cut using one of the two self opening die heads

diameter, the threads are cut using one of the two self opening die heads

supplied with the machine:

2” head (part no. 162151) used to thread tubes with diameters from 1/2” to 2”.
4” head (part no. 162152 and 16215, depending on the thread standard used, BSPT or

NPT) used to thread tubes with diameters from 2½” to 4”.

Optionally available is a manual die head (part no. 162150) which can be used to thread tubes with

diameters from 1/4” to /8”.

Tubes which can be threaded, cut or reamed

The tubes which can be used on the 162140 are defined by the following standards (refer to the

editions published in your language):

1. Stainless steel tubes

EN ISO 1127 June 1996

Stainl ess steel tubes - Dimensions, tolerances and conventional linear densities

EN 10216-5 March 2005

Seamless steel tubes operating under pressure - Technical delivery conditions

Part 5: Stainless steel tubes
EN 10217-7 August 2005

Welded steel tubes operating under pressure - Technical delivery conditions

Part 7: Stainless steel tubes

2. Carbon steel tubes:

EN 10208-2 October 1996

Steel tubes for carrying combustible fluids - Technical delivery conditions

Part 2: Tubes of specification class B
EN 10216-1 December 2002

Seamless steel tubes operating under pressure - Technical delivery conditions

Part 1: Tubes in unalloyed steel with characteristics specified at ambient temperature
EN 10217-1 December 2002

Welded steel tubes operating under pressure - Technical delivery conditions

Part 1: Tubes in unalloyed steel with characteristics specified at ambient temperature
EN 10255 March 2005

Unalloyed weldable and threadable steel tubes - Technical delivery conditions

Important:

not all tubes mentioned in standards prior to standard EN 10255 can be threaded.

Depending on diameter, the thicknesses must be greater than or equal to the thicknesses defined

by standard EN 10255.

–
–
–

–
–

Machine 4 pouces-EN.indd 11

22/08/2007 08:59:13

Summary of Contents for 162140





































































Search results

Summary of Contents for 162140

Reviews:

Related manuals for 162140

Brands by name

Popular brands

Vira 162140, Instruction Manual

Search results

Summary of Contents for 162140

Reviews:

Related manuals for 162140

Brands by name

Popular brands