background image

15

901189 REV D 02/02/17, INST 55-59 CHEV P-UP w/ STANDARD CONTROLS EVAP KIT PG 15 OF 24

NOTE: Vintage Air Systems use 5/8” heater connections. On engines equipped with 3/4” hose 

nipples, these will need to be removed and replaced with 5/8” nipples (not supplied). For water 

pumps with a cast-in 3/4” heater outlet, a 3/4” x 5/8” reducer fitting (not supplied) will need 

to be installed in the heater hose.

From Intake 

Manifold

Figure 14

A/C and Heater Hose Routing 

(1958-59 Models Only)

1.

2.

3.

Locate the #8 compressor A/C hose. Lubricate (2) #8 O-rings (See Figure 11, Page 12) and connect the 135° 

female fitting to the #8 discharge port on the compressor. Then route the straight female fitting with service 

port to the #8 condenser hardline coming through the core support (See Figure 14, below). Tighten each 

fitting connection as shown in Figure 11, Page 12.

Locate the #10 compressor A/C hose. Lubricate (2) #10 O-rings (See Figure 11, Page 12) and connect the 

135° female fitting with service port to the #10 suction port on the compressor. Then route the 90° female 

fitting to the #10 evaporator hardline (See Figure 12, Page 13, and Figure 14, below). Tighten each fitting 

connection as shown in Figure 11, Page 12.
Locate the #6 evaporator/drier hose. Lubricate (2) #6 O-rings (See Figure 11, Page 12) and connect the 

straight female fitting with the binary switch service port to the #6 drier hardline coming through the core 

support. Then route the 90° female fitting to the #6 evaporator hardline (See Figure 12, Page 13, and Figure 

14, below). Tighten each fitting connection as shown in Figure 11, Page 12.

Standard Hose Kit:

1. Refer to separate instructions included with modified hose kit.

Modified Hose Kit:

Tie Wrap

 

 

Heater

Hoses

#6 Drier/Core 

Hardline

095018

Safety 

Switch 

(Binary Type)

 

From Evaporator

to Water Pump

From Heater 

Control Valve to 

Evaporator

#6 Adel Clamp

31602-VUD

#8 Discharge 

Hose

096009

#10 Suction

Hose

096010

Heater Hose

(Heater Control 

Valve/Intake)

NOTE: Flow direction follows

molded arrow on valve.

#6 A/C Hose

096008

#8 Condenser/Compressor

Hardline

095017

#6 Condenser/Drier

Hardline

095016

Summary of Contents for 751155

























Reviews: