13
5.3 Factory reset
Simultaneously long pressing all six pushbuttons resets the device to the factory settings; all other settings will be deleted.
6. Operation
The device has two operating modes:
• With load status display (feedback enabled).
• Without load status display (feedback disabled).
The operating mode is selected by activating or not activating input 8; if the input is activated, feedback is enabled, otherwise feedback is disabled.
6.1 Display of load status (feedback enabled)
This mode is useful in cases where a third-party system controls illumination of the LEDs on the 21126 control; normally the device is in standby condition.
6.1.1 Standby
The brightness level of the six LEDs is that set during the "Standard setup" procedure.
■
If an input is not activated, the colour of the corresponding LED will be white.
■
If the input is activated, the colour of the corresponding LED will be that set using the procedure described in para. 5.1.
■
If a hand enters the proximity detection area, the device will be activated.
6.1.2 Activated
When the device is activated, output 7 is also activated and all the LEDS illuminate at maximum brightness.
■
If an input is not activated, the colour of the corresponding LED will be white.
■
If the input is activated, the colour of the corresponding LED will be that set using the procedure described in para. 5.1.
With independent pushbuttons
The device will activate the corresponding output for as long as the pushbutton is held pressed.
With rocker switches
The device will activate the corresponding output for as long as the pushbutton is held pressed.
A long press of the upper pushbutton activates the "Up" output (Output 1 for the left module, Output 3 for the centre module and Output 5 for the right module)
and it will remain activated for 60 s or until one the two pushbuttons is pressed again.
A long press of the lower pushbutton activates the "Down" output (Output 2 for the left module, Output 4 for the centre module and Output 6 for the right module)
and it will remain activated for 60 s or until one the two pushbuttons is pressed again.
If a change of direction is commanded when the blind is moving, both the corresponding outputs remain off for 500 ms before executing the last command to
be received.
10 s after the hand is withdrawn from the proximity detection area, output 7 is deactivated and the device returns to standby.
6.2 Without display of load status (feedback disabled)
This operating mode is useful in cases where a third-party system does not control illumination of the LEDs on the 21126 control.
In this mode inputs 1 to 6 are ignored and the device is normally in standby condition.
6.2.1 Standby
The brightness level of the six LEDs is that set during the "Standard setup" procedure.
■
If the input is activated, the colour of the corresponding LED will be that set using the procedure described in para. 5.1.
■
If a hand enters the proximity detection area, the device will be activated.
6.2.2 Activated
When the device is activated, output 7 is also activated and all the LEDS illuminate at maximum brightness and in the colours set during the procedure described
in para. 5.1.
With independent pushbuttons
The device will activate the corresponding output for as long as the pushbutton is held pressed; on releasing the pushbutton, the corresponding LED will flash.
With rocker switches
A long press of the upper pushbutton activates the "Up" output (Output 1 for the left module, Output 3 for the centre module and Output 5 for the right module)
and it will remain activated for 60 s or until one the two pushbuttons is pressed again.
A long press of the lower pushbutton activates the "Down" output (Output 2 for the left module, Output 4 for the centre module and Output 6 for the right module)
and it will remain activated for 60 s or until one the two pushbuttons is pressed again.
If a change of direction is commanded when the blind is moving, both the corresponding outputs remain off for 500 ms before executing the last command to
be received.
On releasing the pushbutton, the corresponding LED will flash.
10 s after the hand is withdrawn from the proximity detection area, output 7 is deactivated and the device returns to standby.
Operation
