Vimar 21126 Installer Manual Download Page 11

11

Device configuration

5. Device configuration

Caution: all the procedures described below musty be carried out using the physical pushbuttons, and therefore without the cover plate fitted to the device. 

5.1 Setting the colours of the LEDs 

The colours of the LEDs can be configured in two different ways: 
- via signal on input 7; 
- via local programming procedure.

5.1.1 Configuration via input 7

By providing a signal at input 7 and modulating the pulse width, it is possible to configure the colours of all the LEDs, as indicated in the table below.

Modulation %

LED colour

0 - 13

Custom colour saved to memory (see paragraph 5.1.2)

14 - 27

Blue

28 - 39

Green

40 - 51

Red

52 - 63

Magenta

64 - 75

Cyan

76 - 87

Amber

88 - 100

White

As input 7 has a read error of ± 3% it is advisable to generate an amplitude modulation equal to the average value of the indicated intervals (for example 45% for 
Red).
This configuration method is useful for centralised systems where there is a requirement to change the colours of the LEDs quickly.

5.1.2 Configuration via local programming procedure

If input 7 is not activated or if the signal provided has a pulse width modulation of less than 14%, the colours of the LEDs may be set using the following procedure:
1. Long press the upper configuration button; the device will illuminate all the LEDs with the colour currently saved to memory.

 

At this point it is possible to modify the colour of each individual LED.

2. Short press the pushbutton for which you want to set the colour of the relative LED; each press of the pushbutton will cycle through the available colours in the 

sequence 

Amber - Blue - Green - Red - Magenta - Cyan

.

With a long press on one of the pushbuttons, all the LEDs will cycle simultaneously through the sequence 

Amber - Blue - Green - Red - Magenta - Cyan

3. Once all the desired colours have been selected, long press the upper configuration button to save the settings to memory. 

N.B.

 If no operations are performed within the timeout of 10 s, the device will quit the LED configuration procedure without saving any changes made.

5.2 Device setup

The device setup can be configured in two ways:   
- standard;
- rocker switch action for roller shutters.

5.2.1 Standard setup

1. Long press the upper configuration button; the device will illuminate all the LEDs with the colour white displaying the functions currently saved to memory.

Summary of Contents for 21126
















Reviews: