background image

11

8. BUTTON FUNCTIONS

The surface-mounting timer-thermostat 01911 is used and pro-
grammed with:
• the selection button;
• the rotary knob;
• the vertical sliders.

8.1 

 

 

selection button

The push-button, pressing it briefly, is used to confirm selections 
when scrolling through the menus or to confirm actions of program-
ming; pressing and holding it down, instead, accesses or exits the 
menu. In addition, in some cases, it can also be used to pass from 
one operating mode to another (for example from Automatic to 
Manual).

8.1.1 Pressing the selection button  

• When the timer-thermostat displays the information related to a 

general operating mode (Manual, Automatic, OFF, etc.), on quickly 
pressing the push-button, the device:

- switches onto Manual if it was operating in a different mode;
- switches onto the previously active mode if the timer-thermostat 

was operating in Manual mode;

- if it is on, it deletes the automatic temperature change.

Pressing the selection button for approximately 4 s when the 
timer-thermostat display shows the information related to any 
operating mode accesses the device’s programming menus.

• When the display shows the timer-thermostat programming 

menus, quickly pressing the button confirms access to the menu 
displayed, then accessing the related submenus.

Pressing the selection button for approximately 2 s when the 
timer-thermostat display shows the programming menus exits 
these menus and the device returns to the currently active 
operating mode.

Summary of Contents for 01911





































Reviews: