background image

17

4

Feed supply cord up through hole in bottom 

of range back.

1

2

5

1

2

6

Attach ground lead (green) 

with ground screw that was removed.

Attach line #1 (red) and line #2 (black) 

leads to outside terminal. Attach neutral wire (white)

to center terminal on terminal block.

1

1

3

7

1

2

8

Push supply cord toward terminal

block to relieve strain, reattach supply cord strain

relief bracket over supply cord.

Reattach access door.

16

2

1

1

3

2

1

2

Remove access door.

Remove supply cord strain relief 

bracket and three supply cord mounting screws 

on the terminal block.

Electrical Connection (4-wire)

WARNING

Electrical shock hazard.

To avoid risk or electrical

shock, personal injury or death;

grounding product to the frame

of the unit may or may not be permitted

through your local codes. If ground to the

frame is not permitted then a 4 conductor

power cord must be used.

WARNING

Electrical shock hazard.

To avoid risk of electrical shock,

personal injury or death; verify

your appliance has been

properly grounded in accordance with

local codes or in absence of codes, with

the National Electrical Code (NEC).

ANSI/NFPA 70-latest edition.

2

1

3

Remove grounding screw. Cut-off 

and discard ground strap.

See “Electrical Requirements” information.

Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.

The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.

Summary of Contents for Professional Custom VISC5304B















Reviews: