background image

13

1

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

1

1

2

3

2

2

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Legs are packed in styrofoam top pack. 

Note:

Legs should be installed near to where

appliance is to be used, as they are 

not secure for long transit.

Note: 

It is strongly recommended

that a pallet or lift jack be used rather than tilting.

Raise unit about a foot. Unscrew temporary legs from

couplings. 

4

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Lower range gently to keep any undue strain from

legs and internal mounting hardware.

3

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Screw legs into couplings on all 

four corners.  

Leg Installation

12

WARNING

DANGER

CAUTION

FOR YOUR SAFETY

To avoid risk of personal injury or product

damages, 

DO NOT

use the handle or

oven door to lift the oven. Remove door

before installation to ensure that it is not

used to lift the unit. 

DO NOT

lift or carry

the door by the handle.

Removing the door must be done by your

dealer, or a qualified licensed plumber

.

Door Removal

1

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Open door completely. Place pins, 

supplied with unit, in pin hole. For personal safety,

ONLY use pins supplied with the unit.

2

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Remove hinge trim screws. Take off hinge trim. Identify

right and left hinge for future re-installation.

3

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Close until pins stop door.

4

HO

T

RE

AR

FR

ON

T

HO

T

RE

AR

FR

ON

T

Lift door up and out.

Installation

Summary of Contents for Professional Custom VISC5304B















Reviews: