background image

Features

Applications

Specifications

www.VikingElectronics.com 

Information: 715-386-8861

Touch-Free VoIP Entry Phones

•  Touch-Free motion sensor with adjustable range from one to four inches 
•  Motion Sensors Ring LED lights Blue during idle, flashes Green during dialing and lights 

steady Green when call is answered 

•  Automatic polling and programming software included  
•  2 Amp relay contacts for door/gate or SL-2 strobe light control  
•  SIP compliant 

(see page 2 for list of compatible IP-PBX phone systems) 

•  Outbound Proxy, Authentication ID, Peer to Peer, VLAN Tagging

 

•  PoE powered (class 1, <4 Watts) 
•  Automatic Noise Canceling (ANC) feature for proper operation in noisy environments 
•  VoIP eliminates the need for “Push to Talk” mode 
•  Network downloadable firmware 

•   T-10 Torx security screws for added security 
•  Can be used with optional 

RC-4A

 Secure Relay Controller (

DOD 582

•  Marine grade 316 stainless steel prevents corrosion on the stainless steel models 
•  Laser etched graphics on stainless steel models 
•  Programmable to dial up to 5 numbers on busy or ring no answer 
•  Cycles through backup phone numbers on busy or no-answer 
•  Optional Enhanced Weather Protection (EWP), EWP products are designed to meet IP66 Ingress 

Protection Rating, see 

DOD 859

 

•  Hangs up on busy signal, time-out or touch tone command 
•  Remotely programmable  
•  Extended temperature range (-40°F to 140°F) 
•  3 different chassis 
•  Volume adjustments for microphone and speaker 
•  

E-20TF-IP

 surface mounts to a wall or flat sided post 

•  

E-30TF-IP

 is flush mountable using the included rough-in box or can be surface mounted using 

an optional 

VE-5x5

 Surface Mount Box (

DOD 424

•  

E-32TF-IP

  flush  mounts  in  a  standard  double  gang  electrical           box  (not  included)     

•  Diagnostics 

for testing microphone, speaker, and relay 

Power:  

PoE class 1 (<4 watts) 

Maximum Sound Pressure: 

90 dB SPL @ 1m. 

 

Dimensions: 

See Installation and Specifications

 

Operating Temperature: 

-40°F to 140°F (-40° C to 60° C) 

Humidity - Standard Products:

  5% to 95% non-condensing 

Humidity - EWP Products:

  Up to 100% 

Audio Codecs: 

 G711u, G711a, G722 

Network Compliance: 

 IEEE 802.3 af PoE, SIP 2.0 RFC3261, 

100BASE-TX with auto cross over 

Regulatory Compliance: 

FCC Part 15, Canada ICES-3 Class A, CE 

(except for 

E-20TF-IP

 and 

E-20TF-IP-EWP

)

 

Connections: 

 (1) RJ45 10/100 Base-T, (3) gel-filled butt 

connectors

      Installation requires the assistance of a Network Administrator / IT Technician.

!

The 

E-20TF-IP, E-30TF-IP and E-32TF-IP

 Touch-Free VoIP Entry Phones  are equipped 

with Vikings touchless motion sensor. A simple wave over the sensor will activate a call. 

Touch-Free calling eliminates the exposure to germs and bacteria from typical push button 

switches. 
The Entry Phones are designed to provide quick and reliable handsfree communication 

for SIP VoIP phone systems     with PoE.  They can be programmed from any Touch Tone 

phone, PC, or remotely using a static IP address. The Entry phones can dial up to 5 

programmable numbers. On-board 2 Amp relay contacts are provided for activating 

doorstrikes or gate controllers. An optional 

RC-4A

 Secure Relay Controller can also be 

used. 
The 

E-20/30/32TF-IP

 entry phones motion sensor LED lights blue during idle, flashes 

green during dialing and automatically lights solid green when the call is answered.  
The 

E-20/30/32TF-IP-EWP 

shares all the features of the standard  

E-20/30/32TF-IP 

in 

addition to Enhanced Weather Protection (EWP) for outdoor installations where the unit 

is exposed to precipitation or condensation.  EWP products are designed to meet IP66 

standards and may feature foam rubber gaskets, sealed connections, gel-filled butt 

connectors, as well as potted circuit boards with internally sealed, field-adjustable trim 

pots and DIP switches for easy on-site programming. For more information on EWP, see 

DOD 859

.    

E-20TF-IP / E-20TF-IP-EWP

 

Surface Mount, Light Grey 

UV Stable Plastic Chassis

       E-32TF-IP / E-32TF-IP-EWP

 

Flush Mount in a Standard Double 

Gang Electrical Box,  Brushed 316 

Stainless Steel 

•  Contactless way to initiate a call, reducing the spread of germs 

and bacterias 

•  Gesture Activated Calling 
•  Gate Entrance 
•  Parking ramps/lots 
•  ATM machines 
•  Medical centers

 

•  Lobbies 
•  Entryways 
•  Stadiums 
•  Convention centers 
•  Public access areas

E-30TF-IP / E-30TF-IP-EWP

 

Flush Mount, Brushed 316 

Stainless Steel 

PRODUCT 

MANUAL

Designed, Manufactured and Supported in the USA

E-20/30/32TF-IP

 

Touch-Free  

VoIP Entry Phones 

August 12, 2021

SECURITY & 

COMMUNICATION

VIKING

Summary of Contents for E-20TF-IP
























Reviews: