background image

Specifications

Information:  715-386-8861 

www.VikingElectronics.com

•  Large 10-inch diameter horn 
•  Fully adjustable mounting hardware included 
•  Quick and easy installation 
• SIP compliant, see page two for more information 
• PoE powered (class 3, <13 Watts) 
• Paging prioritization 
• Plays audio from standard multicast sources 
• SIP endpoint or multicast group member 
• Red call status LED indicator 
• Automatic Noise Canceling (ANC) feature for operation in noisy 

environments 

•  Model 

300TB-IP-EWP

 comes with Enhanced Weather Protection 

(EWP), and is designed to meet IP66 Ingress Protection Rating when 

mounted with horn pointing downward at least 45 degrees from 

horizontal. For more info on Enhanced Weather Protection (EWP), see 

DOD 859. 

• Proprietary VOX switching eliminates the need for “Push to Talk” mode 
• Selectable auto-answer feature for monitoring 
• Compatible with Polycom multicast paging 
• Built-in high-efficiency 6 Watt class D amplifier 
• SIP/Multicast:  SIP page, SIP page and zoned multicast receive 
• Support for access code to prevent unwanted SIP calls 
• Hangs up on:  busy signal, time-out, or touch tone command 
• Network remote speaker volume control 
• Automatic Gain Control (AGC) to automatically increase ring volume to 

compensate for ambient noise 

• Diagnostics for testing microphone and horn driver 
• Programmable pre-page alert tone

Power: 

 PoE class 3 (<13 Watts) 

Dimensions: 

 10.0” (23.4 cm) diameter, 11.5” (29.2 cm) long 

Shipping Weight: 

 4.1 lbs (1.86 kg) 

Operating Temperature: 

 -40° F to 140° F (-40° C to 60° C) 

Humidity - Standard Product: 

 5% to 95% non-condensing 

Humidity - EWP Product:  

Up to 100% 

SIP Audio Codecs: 

 G711u, G722 and G711a  

Multicast Audio Codecs: 

 G711u and G722  

Network Compliance: 

 IEEE 802.3 af PoE, SIP 2.0 RFC3261, 

100BASE-TX with auto cross-over 

Regulatory Compliance: 

CE, FCC Part 15 and Canada ICES-003 Class A 

Maximum Output Level:

  113 dB SPL @ 1M  

Amplifier:

  6 Watt class D  

Connections

:  (1) RJ45 10/100 Base-T, (2) butt connectors

The 

300TB-IP

 Paging Horn with Talk-Back can be used for: standard one-

way SIP endpoint paging, two-way conversations via SIP endpoint paging, 

one-way multicast paging, and making standard or emergency two-way SIP 

calls initiated from the optional auxiliary switch input. The microphone 

enables talk-back and also monitors room noise to automatically increase 

the speaker volume when necessary.  
An optional auxiliary switch input allows a hard wired button or switch to 

initiate a SIP call. The button can be mounted on the wall or concealed under 

a desk, etc. A momentary button press will initiate a standard call, while 

holding the button for 3 or more seconds will initiate an emergency call. 
The 

300TB-IP 

features a high efficiency 6 Watt class D amplifier capable of 

driving the horn at up to 113 dB SPL at 1 meter. 
The 

300TB-IP-EWP 

shares all of the features of the 

300TB-IP

 in addition 

to Enhanced Weather Protection (EWP) for outdoor installations where the 

unit is exposed to precipitation or condensation. EWP products are designed 

to meet IP66 standards. For more information on EWP, see 

DOD 859.

 

• Amplified SIP endpoint or multicast IP paging for: Schools, Hospitals, 

Retail Stores, Office Spaces, etc. 

• Provide background music and sound masking 
• Make standard and/or emergency SIP phone calls via handsfree talk-

back speaker 

• Background music and emergency calls for: commercial buildings, 

distribution centers, service/shop areas, gas stations, indoor/outdoor 

recreation and sports facilities, transport terminals, etc.

IP Paging Horn for SIP Endpoint Paging or Multicast Paging /  

Background Music, and Making Standard or Emergency SIP Calls

Applications

Installation requires a Network Administrator / IT Technician

!

PRODUCT 

MANUAL

Designed, Manufactured and Supported in the USA

300TB-IP

 

SIP / Multicast  

Talk-Back Paging Horn 

June 29, 2021

SECURITY & COMMUNICATION

VIKING

Features

Summary of Contents for 300TB-IP



























Reviews: