background image

41

Coding

Coding in the delivered condition

Possible change

System design

00 :1

System version 1:
1 heating circuit without
mixer A1, without DHW
heating 

00 :2

System version 1:
1 heating circuit without
mixer A1, with DHW heat-
ing 

00 :3

System versions 2 and 3:
1 heating circuit with mixer
M2, without DHW heating 

00 :4

System versions 2 and 3:
1 heating circuit with mixer
M2, with DHW heating 

00 :5

System versions 2 and 3:
1 heating circuit without
mixer A1; 1 heating circuit
with mixer M2, without
DHW heating 

00 :6

System versions 2 and 3:
1 heating circuit without
mixer A1; 1 heating circuit
with mixer M2, with DHW
heating 

Boiler/burner

06:...

Maximum limit of the
boiler water temperature,
defaulted by the boiler
coding card

06:20
to
06:127

Maximum limit of the boiler
water temperature within
the ranges specified by the
boiler

21:0

No maintenance interval
(hours run) selected

21:1
to
21:100 

The number of hours run
before the burner should
be serviced is adjustable
from 100 to 10 000 hours
(each step represents
100 hours)

23:0

No time interval for
burner service

23:1
to
23:24

Interval adjustable from 1
to 24 months 

Codes

Code 2

 (cont.)

5692 774 GB

Summary of Contents for Vitoladens 300-C









































































































Reviews: