background image

143

B

A

1 2 3

A

Blocking the boiler externally
(floating contact for switching LV)

B

Start the boiler externally as the last one in the boiler sequence
(floating contact for switching LV)

Con-
tact

Closed

Open

A

– The boiler is blocked and

has been removed from
the boiler sequence.

– Butterfly valve is closed

and the boiler circuit
pump stops.

– The other boilers provide

the required heating.

The boiler is integrated into
the current boiler sequence.

B

This boiler is started if the
other boilers in the heating
system cannot provide suf-
ficient heat.

The boiler is integrated into
the current boiler sequence.

External control of the modulating burner

Make connections at plug 

aVH

 and 

aBÖ

.

Note
The contact at terminals 2 and 3 of plug 

aVH

 is always required to

prevent boiler damage.
This contact must always be closed on the lead boiler.

STB

ON

TR

ON

TR

N

STB

B

G

D

E

41

B4

L

S3

N

T1

T2

41

L

B4

S3

T2

T1

N

F

146

A

12

3

T6 T7 T8

90

C

A

/

B

Boiler enable from on-site modulation controller (butterfly
valve open)

A

Floating contact for switching LV

B

Floating contact for switching 230 V~

C

Burner base load
(floating contact for switching 230 V~)

D

T6, T7: Reduce burner output (modulation controller closed)
(floating contact for switching 230 V~)

E

T6, T8: Increase burner output (modulation controller open)
(floating contact for switching 230 V~)

F

Plug to the burner

G

Plug to the control unit

Note
If the boiler is enabled via a contactor, the conditions of safety category
II and the operation of safety LV (SELV) must be ensured.

Contact Closed

Open

A

/

B

Boiler enabled. The butter-
fly valve opens.

The butterfly valve is closed
after approx. 5 s. External
burner start not possible.

C

Burner on (base load). An
on-site modulation control-
ler regulates the load-de-
pendent modulation. The
boiler water temperature is
restricted by the electronic
maximum temperature lim-
iter.

Burner off.

Hook-up of on-site control units via LON

The Vitotronic control units are equipped with an open standard LON
interface. With standard LONWORKS network variables (SNVT).
This universal, decentralised network for automated building control
systems not only allows communication between Vitotronic control
units, but also the hook-up of on-site systems and devices from various
manufacturers.

It enables, for example, individual room control units or building man-
agement systems to be directly connected to Vitotronic control units.
Further information can be found in the LON manual; see
www.viessmann.de\lon.

Control units

 (cont.)

94

VIESMANN

Gas condensing boilers

9

5822 449 GB

 

Summary of Contents for Vitocrossal 200 CM2 Series





































































































Reviews: