Viessmann Vitocrossal 200 CM2 Series Technical Manual Download Page 80

Page: 80 / 100

Immersion temperature sensor

Part no. 7438 702

To capture the temperature in a sensor well.

Specification

Cable length

5.8 m, fully wired

IP rating

IP 32 to EN 60529, ensure
through design/installation

Sensor type

Viessmann NTC 10 kΩ, at
25 °C

Permissible ambient temperature
– During operation

0 to +90 °C

– During storage and transport

−20 to +70 °C

EA1 extension

Part no. 7452 091

Function extension inside enclosure for wall mounting.

Using the inputs and outputs allows up to 5 functions to be ach-
ieved:

1 switching output (floating changeover contact)
■ Switching a feed pump to a substation
■ Signalling reduced mode for a heating circuit

1 analogue input (0 to 10 V)
■ Specifying set boiler water temperature

3 digital inputs
■ External operating mode changeover for 1 to 3 heating circuits (only

with control units for weather-compensated mode)

■ External blocking with central fault message
■ Fault messages
■ Brief operation of the DHW circulation pump (only with control units

for weather-compensated mode)

180

140

Specification

Rated voltage

230 V~

Rated frequency

50 Hz

Rated current

2 A

Power consumption

4 W

Rated breaking capacity of the relay
output

2(1) A 250 V~

Safety category

IP rating

IP 20 D to EN 60529
Ensure through design/instal-
lation

Permissible ambient temperature

– During operation

0 to +40 °C
Installation in living spaces or
boiler rooms
(standard ambient conditions)

– During storage and transport

–20 to +65 °C

Vitocom 100, type LAN1

For part no., see the current pricelist

For remote control of a heating system via internet and IP networks
(LAN) with DSL router.
Storage combi boiler.
For system operation with

Vitotrol app

Vitodata 100

Functions when operating with Vitotrol app:

■ Remote control of up to three heating circuits in one heating system.
■ Selecting operating programs, set values and time programs.
■ Scanning system information
■ Displaying messages on the Vitotrol app user interface

The Vitotrol app supports the following terminal devices:
■ Terminal devices with Apple iOS operating system version 5.0 and

6.0.

■ Terminal devices with Google Android operating system V. 4.0 and

higher.

Note
For further information, see www.vitotrol-app.info.

Control units

(cont.)

VIESMANN

Gas condensing boilers

5822 449 GB

Summary of Contents for Vitocrossal 200 CM2 Series





































































































Search results

Summary of Contents for Vitocrossal 200 CM2 Series

Reviews:

Related manuals for Vitocrossal 200 CM2 Series

Brands by name

Popular brands

Viessmann Vitocrossal 200 CM2 Series, Technical Manual

Search results

Summary of Contents for Vitocrossal 200 CM2 Series

Reviews:

Related manuals for Vitocrossal 200 CM2 Series

Brands by name

Popular brands