Viessmann H32E Installation And Service Instructions Manual Download Page 26

Page: 26 / 80

Air distribution from air distributor to wall/ceiling/floor
air vents

Installation information:

■

Make all air duct connections airtight.

■

For easier installation, lubricate the seals with lubri-
cating paste before assembly. Only use lubricating
paste intended for EPDM.

Fig. 24

Pos. Components

Header from ventilation unit

Distributor connector DN 125/160/180

2-way air distributor

Distributor connection cover, round

Distributor connection cover, flat

Flat duct connection piece

Flat duct

Locking pin

90° bend, broad side

8-way air distributor, intermediate level

Pos. Components

Mounting ring for supply air/extract air vent

Supply air/extract air vent

Straight through diverter

90° bend, narrow side

Inspection port

Round plastic duct (external

75 or 90 mm)

Cover for round duct connector (

75 mm)

Round duct connector, 1-way (

90 mm) or 2-

way (

75 mm)

Wall/ceiling air vent in "flat design"

Installing modular supply air/extract air ductwork

Modular flat/round supply air/extract air system diagram

5831646

Installation

Summary of Contents for H32E

















































































Search results

Summary of Contents for H32E

Reviews:

Viessmann H32E, Installation And Service Instructions Manual, Page: 26 / 80

Search results

Summary of Contents for H32E

Reviews: