manualshive.com logo in svg

Videx GSM Lite 4000 Series, Technical Manual

Share
Download
Videx GSM Lite 4000 Series Technical Manual Download Page 46

66250756-EN - V2.1 - 05/11/19 

- 46 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

RECORD SHEET

In order to manage the GSM LITE intercom more effectively it is recommended that an up to date record sheet is kept for all the 
programming and system settings stored in the GSM intercom. This will also be useful if any future changes need to be made. The 
following table format can be used to record the GSM’s basic information.

GSM LITE intercom telephone No.

IMEI number

Master code (default 1111)

Master telephone No.

The table format below can be used to record the call button numbers and the divert numbers (from 001 to 004).

BUTTON

MEM. LOCATION

TELEPHONE NO.

USERNAME

Button 1 (primary pn)

STN001

Button 1 (divert dn)

STD001

Button 2 (primary pn)

STN002

Button 2 (divert dn)

STD002

Button 3 (primary pn)

STN003

Button 3 (divert dn)

STD003

Button 4 (primary pn)

STN004

Button 4 (divert dn)

STD004

It is also recommended that a record sheet of the dial to open DTO (

STR

) numbers and username is kept (from 000 to 099), following 

the table format below:

MEM. LOCATION

TELEPHONE NO.

USERNAME

STR000....STR099

User Management

Summary of Contents for GSM Lite 4000 Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands