manualshive.com logo in svg

Videx GSM Lite 4000 Series, Technical Manual

Share
Download
Videx GSM Lite 4000 Series Technical Manual Download Page 18

66250756-EN - V2.1 - 05/11/19 

- 18 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

Auxiliary Inputs/Outputs

AUXILIARY OUTPUT AO1

The auxiliary output AO1 has six modes 00 - 05 and is set using the 

A1M

 command (refer to page nn for full list of 

A1M 

programming 

modes). It is an open collector output (switched low, 150mA max.) and depending on the mode it is set to will determine how the 
AO1 output behaves. The following examples show how the AO1 output can be connected.

AO1 SET TO MODE 00, ‘CALL ACTIVATED’

When set to mode 

00

 auxiliary output AO1 will activate when the call begins and deactivate when the call ends, as shown in 

Fig.16

.

GSM
INTERCOM
Art.4811

AO1 output will activate
for the duration of the call

To Antenna

Fig. 16

 

AO1 SET TO MODE 01,  ‘USER ACTIVATED’

When set to mode 

01

 auxiliary output AO1 will activate when the terminals 

g

 & 

5

 are shorted together on the GSM LITE module or 

by pressing 

6

 on the telephone during a call, as shown in 

Fig.17

. Auxiliary output AO1 will only activate for the programmed time.

GSM
INTERCOM
Art.4811

AO1 output will activate
for the programmed time

OR

To Antenna

Fig. 17

 

Summary of Contents for GSM Lite 4000 Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands