manualshive.com logo in svg

Videx GSM Lite 4000 Series, Technical Manual

Share
Download
Videx GSM Lite 4000 Series Technical Manual Download Page 43

66250756-EN - V2.1 - 05/11/19 

- 43 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

USER COMMAND TABLES

The following user command table shows the user commands that can be carried out during a call. Successful commands are 
signalled by two beeps from the telephone, errors are signalled by four beeps.

IMPORTANT NOTE: When the ED# function has been enabled the user must press the # button on their phone before pressing 
any of the following user commands (also refer to ED# notes on page 38 for further information).

FUNCTION

1st KEY TO PRESS

2nd KEY TO PRESS

Latch the relay (unlatch by pressing 3)

1

0

Release the door or gate

3

n/a

Activate auxiliary output AO1

1 

(when A1M = mode 01)

6

n/a

Adjust door speech volume (GSM speaker)

4

0 - 9 (0 = lowest, 9 = highest)

Adjust phone speech volume (GSM mic)

7

0 - 9 (0 = lowest, 9 = highest)

Status Indication for AO1

2 

(when A1M = mode 02)

9

n/a

1 - 

Activating auxiliary output 

AO1

 in this way is only possible when 

A1M

 mode has been set to mode 

01

 (also see notes on page 

33, 

set auxiliary output AO1 mode

, and 

Fig.17

, on page 18) and will operate for the programmed 

AO1

 time. If the 

AO1

 output 

time has been set to latch simply press 

6

 on the phone to unlatch the output again.

2 - 

Auxiliary input 

AO1

 status indication is only possible when 

A1M

 mode has been set to mode 

02

 (also see notes on page 33, 

set 

auxiliary output AO1 mode

, and 

Fig.18

, on page 19).

The next user command table shows the SMS text messages that can be sent to the GSM LITE intercom while in standby (the 
examples shown in the table use the default 4 digit master code 1111).

FUNCTION

MESSAGE TO SEND

Check the signal strength

1111SIG?

Check the available balance

3

1111BAL?

Check the software version

1111VER?

Release the door/gate

1111RLY? (? optional, send if confirmation is required)

Latch the relay

1111RLA? (? optional, send if confirmation is required)

Unlatch the relay

1111RUL? (? optional, send if confirmation is required)

Activate auxiliary output AO1

1111A1O? (? optional, send if confirmation is required)

Latch auxiliary output AO1

1111A1L? (? optional, send if confirmation is required)

Unlatch auxiliary output AO1

1111A1U? (? optional, send if confirmation is required)

Check Input Status

1111CHK? (also see notes on pages 36 - 37)

Find a Dial to Open (DTO) number (000 - 
999)

1111FDT”yyyyyyyyyyy”? (where yyyyyyyyyyy = telephone number, minimum of 4 
digits, also see notes on page 38)

3 - 

The balance can only be checked if the correct balance check string has been stored (also see 

SDL

 notes on page 35). This feature 

is only applicable for pay-as-you-go SIM cards.

User Commands

Summary of Contents for GSM Lite 4000 Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands