Vi-K2/Vi-K3 Universal
Keyboard
Vi-K2 Universal Keyboard User Manual
12
•
Enter the password using the number keys
1
,
2
,
3
,
4
,
5
,
6
,
7
,
8
,
9
and
ZERO
(the factory default
password is
123456
). Note that only the last 3 digits are displayed.
•
Press
the
OK
key.
•
If the password is rejected, the word “
Rej
” will be displayed;
•
If the password is accepted, the display will flashing ”
C1.1
”. The Vi-K2/Vi-K3 is now in
Configuration Mode
. While is configuration mode, the display will always be flashing.
2.2.3
Selecting Dome Protocol for the “
DOMES-1
” output
•
Make sure that you are in
Configuration Mode
as detailed in section 2.2.2.
•
Press
the
DOME
key.
•
Press
the
BACK
key to select “
DOMES-1
”
output.
•
Enter the protocol you require by pressing two number keys (refer to section
Error! Reference
source not found.
). E.g.
1
followed by
2
would select Borsatec (protocol 12).
2.2.4
Selecting Dome Protocol for the “
DOMES-2
” output
•
Make sure that you are in
Configuration Mode
as detailed in section 2.2.2.
•
Press
the
DOME
key.
•
Press
the
OK
key to select “
DOMES-2
”
output.
•
Enter the protocol you require by pressing two number keys (refer to section
Error! Reference
source not found.
). E.g.
1
followed by
2
would select Borsatec (protocol 12).
2.2.5
Assigning cameras to the “
DOMES-1
” or “
DOMES-2
” outputs.
Following a factory reset, all cameras are allocated to the “
DOMES-1
” output. If only one type of dome is
being used, this section can be skipped.
If two types of dome are to be controlled, all domes of one type should be connected to the “
DOMES-1
”
output and all domes of the other type should be connected to the “
DOMES-2
” output. Program the Vi-
K2/Vi-K3 to tell it which domes are connected to which outputs as follows:
•
Make sure that you are in
Configuration Mode
as detailed in section 2.2.2.
•
Press
the
UNIT
key and select the unit address (usually
1
if only one Vi-series being controlled)
•
Press
the
CAMERA
key, and select a camera that is to be assigned. The LED display indicates the
camera number
1
to
16
and the currently assign dome output
1
or
2
. For example, the display
“
C7.2
”
would
indicate that camera 7 is controlled via the “
DOMES-2
”
output
.
•
Press
the
BACK
key to select the “
DOMES-1
” output or press the
OK
key to select the “
DOMES-
2
” output.
•
Repeat for all units and cameras as required.
2.2.6
Enabling Display Monitors
Each Vi-K2/Vi-K3 keyboard can be set to have control of a limited choice of displays. For example, you may
want one Vi-K2/Vi-K3 to be able to select cameras for the spot monitor (i.e. display
2
) whilst another Vi-
K2/Vi-K3 can select cameras for the main monitor (i.e. display
1
).
•
Make sure that you are in
Configuration Mode
as detailed in section 2.2.2.
•
Press
the
DISPLAY
key and select a display that you wish to enable or disable by using the
number keys.
Summary of Contents for Vi-K2
Page 2: ......
Page 20: ...Vi K2 Vi K3 Universal Keyboard Vi K2 Universal Keyboard User Manual 18...
Page 107: ......
