Victron energy Lynx Distributor Manual Download | Manualshive

Page: 25 / 31

background image

The VictronConnect App Lynx Smart BMS showing Lynx Distributor status

Fuse blown alarm

This alarm is raised if a fuse has blown. The fuse status will change in the VictronConnect App and an alarm message is
displayed. The alarm message will also be shown on a connected GX device and the VRM portal. The fuses are numbered from
left to right.

NOTE: These alarm codes are a workaround until the Lynx Smart BMS is supported in VenusOS. The alarm message on the GX
device or the VRM portal will be similar to the message shown in the VictronConnect App.

Table 4. Lynx Distributor fuse blown alarm codes

Alarm

Description

#201

Distributor A, Fuse 1 blown

#202

Distributor A, Fuse 2 blown

#203

Distributor A, Fuse 3 blown

#204

Distributor A, Fuse 4 blown

#205

Distributor B, Fuse 1 blown

#206

Distributor B, Fuse 2 blown

#207

Distributor B, Fuse 3 blown

#208

Distributor B, Fuse 4 blown

#209

Distributor C, Fuse 1 blown

#210

Distributor C, Fuse 2 blown

#211

Distributor C, Fuse 3 blown

#212

Distributor C, Fuse 4 blown

#213

Distributor D, Fuse 1 blown

#214

Distributor D, Fuse 2 blown

#215

Distributor D, Fuse 3 blown

#216

Distributor D, Fuse 4 blown

Lynx Distributor

Page 22

Operation Lynx Distributor

«
...
23
24
25
26
27
...
»

Summary of Contents for Lynx Distributor
































Reviews:

No comments

Related manuals for Lynx Distributor

WIFI SMART BULB Series

Brand: IQlife Pages: 12

Smart WiFi Plug

Brand: Iluv Pages: 4

b@home gate MGCBB-064.360

Brand: alre Pages: 3

Brand: Enerwave Pages: 2

Brand: Sharper Image Pages: 4

Brand: Sonoff Pages: 8

Brand: HAI Pages: 70

Holec Capitole 40

Brand: Eaton Pages: 101

Brand: S&C Pages: 41

SmartHome VS-SH2000-000

Brand: Vivint Pages: 2

Brand: Gocontrol Pages: 2

Brand: Bintronic Pages: 6

Brand: Bintronic Pages: 19

Brand: Bintronic Pages: 31

homee CentronicPlus Cube

Brand: Becker Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands