background image

12

 

 

-

 

Check  and  verify  the  correct  installation  of  the  components  in  the  system  and  also  is  the  system 

equipped  with  appropriate  expansion  tank  to  ensure  safe  work.  The  presence  of  heat  expansion  tank  in  the 
stove itself, does not guarantee adequate protection from overheating the water. 

-

 

Connect the electric supply and make a cold test (performed by the dealer)  

-

 

Fill up the system form the filling tap (recommended not to exceed 1 bar pressure.) 

During filling up the system, bleed the circulation pump.  

 

Warning ! 

During  first  start  up  purge  the  system  using  valve  at  the  top  of  the  stove.  This  operation  must  be 

performed again in the first days of use and when the system is topped up. The presence of air in the system of 
pipes could result improper work of the appliance. For easier work, there is a plastic tube available to the valve. 

The  stove  is  painted  with  heat  resistant  paint.  The  paint  is  resistant  to  high  temperatures,  but  it  is  not 

resistant to rust. Please do not  place  any objects on the stoves  paint.  If there is a dust,  the cleaning must  be 
done with smooth brush. Never use water or cloth! 

During the first ignition it is necessary to “bake” the paint to harden it. This must be done with very slightly 

opened door. During this procedure, do not put anything on the stove and do not touch the external parts to 
avoid damaging the paint. There will be slight smell, which is a result from the paint hardening. This is normal 
and will disappear in few hours. Please unsure good ventilation in the room during this procedure.  

If in a result of overheating or not proper use the color is changed, there are spots of rust or there is damage on 
the paint, do not worry. You can order the proper spray paint to your dealer. 
Before igniting please check:  
The  installation  is  correct.  Check  the  electric  supply;  the  door  is  closed  with  proper  seal;  the  combustion 
chamber is clean; the display is on stand-by (time and date set)  
 

12.Instructions for use: 

Feeling the feed screw: 
When the tank for pellets is completely empty this means that the feed screw is also empty. Before re-igniting 
the stove you must fill it up following the next steps: press b/- simultaneously (by the control panel) for 
a  few  seconds.  After  the  keys  are  released  in  few  seconds  “Reload”  will  appear.  It  is  normal  some  pellets  to 
remain  in  the  hopper,  because  the  screw wasn’t  able  to  pick  them  up.  Once  a  month  vacuum  the  hopper  to 
prevent clogging from dust.  
During the first start up of the stove (or after reloading pellets when completely emptied) it is possible the start 
up procedure to be repeated.  
Automatic ignition: 
When the stove is on stand-by position, press button 0/1 for 2 seconds (via remote control or control panel). 
This will trigger the ignition process. “Start” will appear on the display and countdown will be started in seconds 
(1020).  There  is  no  time  to  adjust  the  ignition  process:  the  duration  will  be  automatically  shortened  if  the 
control board detects that certain test are performed previously. The flame will appear in 5 minutes 

 

Manual ignition (in case of start-up failure) 
If the  temperature is lower than 3  ˚С  it  is too low  for the  igniter to heat  up  enough to start  the  fire or if the 
resistance is temporary not working, you can use a firelighter to ignite the stove.  
Place the  firelighter in the combustion chamber, close  the door and pres 0/1 on the control panel (or on the 
remote). 

 

13.Operating modes: 

 

Working with the control panel, when the stove is working or in stand-by position.  
-

 

press: + or – button, to increase or decrease the desired temperature of the water. 

-

 

With pressing the “boiler” button you can change and set the desired temperature in the boiler or with 

+/-  to  change  the  temperature  of  the  secondary  circuit.  It  is  possible  to  see  (if  the  boiler  is  connected)  the 
temperature of the boiler or external storage by pressing the boiler button and the previously set temperature 
will  be  displayed.  By  pressing  +/-  you  can  change  the  parameter.  If  the  boiler  sensor  is  not  connected  the 
following will appear on the display. “--.- ˚С”. 

 

Shutdown: 

Summary of Contents for Vittoria B Series






















Reviews: