background image

4 | VWG-50-Installation Manual 

 

P

ARTS 

A

VAILABLE

 

Part

 

number

 

Description

 

 
 

VWG-50-5000 

Viconics BACnet™™ over MS-TP & IP wireless gateway. 
Includes: 
Supports up to 50 wireless controllers 
Factory mounted wireless adapter 
24 VAC panel mounted power supply 
Gateway mounted antenna 

 

VWG-RA 

Remote antenna for gateway when the gateway is installed 
inside a metal cabinet or when remote antennal mounting is 
required by physical installation 

VWG-WA 

Replacement antenna for gateway mounted antenna setup 

VWG-PS-AC 

120 VAC to 15 VDC power supply for VWG with cord 

VWG-BB 

Replacement battery backup pack for the VWG 

 

P

REPARATION

 

 
Unpack the VWG and power module (either 

VWG-PS-DC

 or 

VWG-PS-AC

) and inspect the 

contents of the packages for damaged or missing components. Be sure the factory-installed 
ferrite is on the cord of the power supply unit. If damaged, notify the appropriate carrier at 
once and return any damaged components for immediate repair or replacement.  

 

Included in this Package 

 

Included in this package you should find the following items: 
 

 

VWG-50-XX-1000 base controller. 

 

Local antenna for the VWG 

 This 

VWG-50-XX-1000

 Hardware installation guide 

 

Configuration tool on a mini-CD

 

 

 

Power module required for operation, are ordered and sold separately. The power 
module can be one of the following: 
– 

VWG-PS-DC: 24VAC in-line (DIN-mount capable), 

or 

– 

VWG-PS-AC: External 120 VAC wall-mount power adapter

 

 
 

 

 

Summary of Contents for VWG-50-5000





















Reviews: