manualshive.com logo in svg

Vicon V1400X-DVC-3, Instruction Manual, Page: 45 / 67

Share
Download
Vicon V1400X-DVC-3 Instruction Manual Download Page 45

38  

•

  Operation: 1400 Series Only 

XX090-02-00 Rev 1102 System Console 

Alarm Dwell 

 
To set the alarm dwell time: 
 

1.  Enter a number for the dwell time (1 - 60 seconds). 

2.  Hold the bottom right soft key down and press the Dwell soft key at the same time. 
 

Operation: 1400 Series Only 

Tours 

 
To start a tour: 
 

1.  Enter the tour dial-up number and press the Tour soft key to start the tour. 

2.  Press the Tour key again to advance a step in the running tour. Press the Cancel soft key to stop the 

tour. 

 
To activate a quick-access tour: 
 

1.  Enter a “9” followed by the tour dial-up number. 

2.  Then press the Tour soft key.  

3.  Press the Tour soft key again to start the tour. Press the Cancel soft key to stop the tour. 

Salvos 

 
To start a salvo: 
 

1.  Enter the salvo dial-up number. 

2.  Press the Camera soft key.  

Home Position 

 
To go to the home position: 
 
Press the Preset key twice to call up preset position 1. 

Alarms 

 
For any active alarm, the control screen will display a flashing Alarm soft key label and the status line will 
display the alarm title. To acknowledge an alarm (refer to the control system manual for more information): 
 

Summary of Contents for V1400X-DVC-3




































































Reviews:

No comments