manualshive.com logo in svg

Vicon V1400X-DVC-3, Instruction Manual, Page: 13 / 67

Share
Download
Vicon V1400X-DVC-3 Instruction Manual Download Page 13

6  

•

  Installation: AURORA/VCR ONLY 

XX090-02-00 Rev 1102 System Console 

Installation: AURORA/VCR ONLY 

Make connections as shown in the figure and tables below. Refer to the Reference chapter for cable 
recommendations.  
 

250V SB

2A  10-12VAC

RISK  OF  FIRE REPLACE 

FUSE AS  MARKED

CAUTION

PWR/COMM

JOYSTICK

RS232/RS485

AUX

CONTROL OUT

+ AC –

1

Connect the appropriate power 
supply to this connector: 

V1400X-PS for 120 VAC 
V1400X-PS-230 for 230 VAC.

Connect to 
V1400X-DJT or
V1400X-JST.

This connector not 
used in AurorA/VCR 
Only mode.

This connector is not 
used in AurorA/VCR 
Only mode.

For A99 Protocol: Connect to MIU(s) 
to use VCRs and/or AurorA99/AurorA 
multiplexers.

For A2000 Protocol: Connect directly 
to RS-485 devices using Vicon's 
AurorANet protocol. Note that the 
V800MIU-3 uses AurorANet protocol   
and must be used to connect to 
AurorA99/AurorA multiplexers and 
VCRs.

Note: You must choose A2000 or A99 
protocol during programming. You 
may not mix both protocols on one 
system console.

*

*

Connect to RS-485* or RS-232  
device(s). Connect to auxiliary 
devices.

Pin No.

RS-485

RS-232

Signal Name

RS485 + (A)
RS485 – (B)
Ground

1
6
7

Pin No.

Auxiliary Devices

Signal Name

Ground
Aux 1
Aux 2

7
8
9

Pin No.

Signal Name

TxD
RxD
RTS
CTS
Ground

2
3
4
5
7

RS232
RS485

AUX

System Console "RS232, 
RS485, AUX" Connector.

SYSTEM CONSOLE REAR PANEL

8000-8595-00-00

8002-9338-00-00

8000-8594-05-00

 

8004-8526-01

 

Figure 4 

AURORA/VCR ONLY Installation 

Summary of Contents for V1400X-DVC-3




































































Reviews:

No comments