manualshive.com logo in svg

Viatron KNX IR Linker, Manual

Share
Download
Viatron KNX IR Linker Manual Download Page 20

 

Seite 20 von 22 

 

10

 

Important information 

10.1

 

Disclaimer 

Despite  the  examination  of  the  contents  of  this  print-out  for  conformity  with  the 
hardware and software deviations are not always completely excluded. Therefor we are 

unable to offer any legal guarantee for its correctness. Necessary corrections are taken 

into account in new versions of the manual. 

 
We reserve the right to make technical changes to the products as well as changes to the 

content of this document at any time without prior notice. 

 

Installation  and  assembly  of  electrical  devices  may  only  be  carried  out  by  a  qualified 
electrician.  It  is  essential  to  observe  the  applicable  accident  prevention  regulations. 

Failure to observe the  installation instructions may  result in  damage to the unit itself, 

fire or other hazards. 

This manual is part of the product and must remain with the end customer. 

 

10.2

 

Intended use 

The KNX IR Linker is designed for indoor installation 

 

10.3

 

Warranty 

We provide warranty within the scope of the legal provisions. 

Please  send  the  device  with  a  fault  description  and  in  the  original  packaging  to  our 

service center (Viatron GmbH, Carl-Metz-Str. 3, 76275 Ettlingen) 

 
 

 

 

 
 

 

 

 

 
 

 
 

 
 

 

 

 
 

Summary of Contents for KNX IR Linker























Reviews:

No comments

Brands by name

Popular brands

Load more brands