background image

VAB-630 Android EVK v1.0.3 Quick Start Guide 

1

 

1.

 

Introduction 

This Quick Start Guide provides an overview on how to boot the Android EVK system 
image in the VAB-630 board and configure the supported hardware functions in the 
build.  

The VAB-630 Android EVK v1.0.3 is developed based on Android 5.0.0 (Lollipop) and it 
enables the hardware features of the VAB-630 board. 

 

EVK Package Contents 

1.1.

There are three folders in the package as listed below. 

Firmware folder 

Description 

VAB-630_Android_EVK_v1.0.3.zip 

Android EVK system image and installation script 
files  

Document folder 

Description 

VAB-630_Android_EVK_v1.0.3_Quick_Start 
_Guide_v1.00_20170811.pdf 

Quick start guide 

Tools folder 

Description 

SmartETK_SDK_Sample.apk 

Smart ETK demo program 

BluetoothSPPTest.apk  

Bluetooth SPP testing program 

arm_201103_gcc4.5.2.tgz 

Toolchain 

VAB-630 Android BSP contents 

 

Firmware Folder Contents 

1.1.1.

VAB-630_Android_EVK_v1.0.3.zip:

  

The Android EVK system image and installation 

script files. 

 

Document Folder Contents 

1.1.2.

VAB-630_Android_EVK_v1.0.3_Quick_Start_Guide_v1.00_20170811.pdf: This Quick Start 
Guide provides an overview on how to boot the Android EVK system image in the VAB-
630 board and configure the supported hardware functions in the build.  

 

Tools Folder Contents 

1.1.3.

SmartETK_SDK_Sample.apk: is the Smart ETK demo program. 
BluetoothSPPTest.apk: is the Bluetooth SPP profile test program. 
arm_201103_gcc4.5.2.tar.gz:

 

is a toolchain, which is a set of software development tools 

for building images for the VAB-630 board. 

Summary of Contents for VAB-630



























Reviews: