VIA Technologies EPIA-M860-12E User Manual Download Page 82 | Manualshive

Page: 82 / 84

background image

EPIA-M860 User Manual

71

Appendix B.

Riser Card Modules

There are two riser card modules that are compatible with the EPIA-M860: the PCIE-03 and the EXT-PCI-01.

B.1.

PCIE-03

The PCIE-03 riser card has both a PCI slot and a PCIe x1 slot. This card can only be used if the mainboard has a PCI slot
properly aligned with a PCIe x1 slot. Additionally, the orientation of the PCIe x1 slot must be reversed so that the key
notch is furthest away from the key notch on the PCI slot.

Figure 66: Installing the PCIE-03 riser card

«
...
80
81
82
83
84
»

Summary of Contents for EPIA-M860-12E





















































































Reviews:

No comments

Related manuals for EPIA-M860-12E

Brand: SOLTEK Pages: 49

MYC-C8MMQ6-8E2D-160-I

Brand: MYiR Pages: 50

Brand: Supero Pages: 105

Brand: JETWAY Pages: 44

Brand: Texas Instruments Pages: 47

Brand: DFI Pages: 67

Brand: MATSONIC Pages: 78

Brand: Arbor Technology Pages: 86

Brand: Gigabyte Pages: 96

Brand: Texas Instruments Pages: 26

Brand: Micronics Pages: 63

Brand: 96Boards Pages: 22

ZYNQ XC7Z020-1CLG484C

Brand: National Instruments Pages: 63

Brand: DFI Pages: 183

K10N780SLIX3-WIFI

Brand: ASROCK Pages: 2

Brand: Asus Pages: 58

Brand: Asus Pages: 74

Brand: Asus Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands