VIA Technologies EPIA-M860-12E Page 76 User Manual Download | Manualshive

Page: 76 / 84

background image

EPIA-M860 User Manual

65

6.9.2.10.

PCI LAN S5 Wakeup

The PCI LAN S5 Wakeup feature enables the BIOS to allow remote wake-up from the S5 power off state through the
PCI bus. This feature has two options: enabled and disabled.

6.9.2.11.

EuP/ErP Lot6 Support

The EuP/ErP Lot6 Support feature enables the BIOS to reduce the power draw to less than 1W when the system is in
standby mode. This feature has two options: enabled and disabled.

Note:

When EuP/ErP Lot6 support is enabled, the PCIe LAN remote wake-up capability will be disabled.

«
...
74
75
76
77
78
...
»

Summary of Contents for EPIA-M860-12E





















































































Reviews:

No comments

Related manuals for EPIA-M860-12E

Brand: JETWAY Pages: 46

Brand: MSI Pages: 92

phyCORE-ADuC812

Brand: Phytec Pages: 86

Brand: AMPTRON Pages: 41

Brand: MATSONIC Pages: 78

Brand: JETWAY Pages: 44

DUOX Programmer

Brand: Fermax Pages: 99

Brand: AOpen Pages: 8

Brand: TYAN Pages: 47

Brand: Analog Devices Pages: 16

Brand: Avalue Technology Pages: 80

Brand: ASROCK Pages: 38

Brand: Rohm Pages: 8

Desktop Board D850EMD2

Brand: Intel Pages: 24

Brand: Asus Pages: 64

Brand: Asus Pages: 64

Brand: Asus Pages: 66

Brand: Asus Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands