VETRON 5000 Instruction Manual Download Page 28

Page: 28 / 83

07/2020

VETRON 5000/5100 - FLAT BED MACHINE - INSTRUCTION BOOK

03. OPERATION OF THE MACHINE

01.01.

INSERTING THE NEEDLE (2- NEEDLE)

-2-2

CAUTION! RISK OF INJURY!

Push the X-button at the machine head, the red light illuminates showing the active

“BLOCKED MODE“

, or turn the machine off before inserting the needles. Failure to

comply produces a risk of injury in case of an unintentional machine operation.

INFO

Only use needles from the system intended for the machine.
(Needle system 134-35)

01. Push the X-button at the machine head, the red light illuminates showing

the active

“BLOCKED MODE”

, or turn the machine off.

02. Loosen the screws

03. Push the needles

fully in until they stop. Make sure that the groove

of the right needle points to the right and the left needle to the left.

04. Tighten the screws

again.

05. Push the X-button or switch the machine on again and follow the instructions

displayed on the control panel.

NOTE:

Before activating the machine by the X-button make sure to remove

sewing material

other items

below the sewing feet if necessary and

follow the instructions displayed on the control panel.

Summary of Contents for 5000




















































































Search results

Summary of Contents for 5000

Reviews:

Related manuals for 5000

Brands by name

Popular brands

VETRON 5000, Instruction Manual

Search results

Summary of Contents for 5000

Reviews:

Related manuals for 5000

Brands by name

Popular brands