manualshive.com logo in svg

VETRON 5000, Instruction Manual

Share
Download
VETRON 5000 Instruction Manual Download Page 9

07

07/2020

VETRON 5000/5100 - FLAT BED MACHINE - INSTRUCTION BOOK

01. PREFACE

03. 

DANGER NOTES

1

 THREAD TAKE UP LEVER

6

 EYE GUARD

2

 SEWING ZONE

7

 FINGER GUARD

3

 BOBBIN THREAD WINDER

5

 SAFETY SPRING

4

 ZONE BETWEEN MACHINE AND TABLE

CRUSHING 

Crushing and bruising through the thread take up lever 

1

 

Make sure thread take up lever guard is mounted.  
Risk of injury due to movement of the lever.

CRUSHING 

Crushing and bruising through the needle and sewing feet 

2

 

Make sure finger guard is mounted. 
Risk of injury through needle and feet movement.

DANGER OF CUTS 

Cuts through rotation 

3

 

Keep distance from bobbin winder while winding. 
Risk of injury due to rotation.

CRUSHING 

Crushing and bruising due to tilting the machine 

4

 

Make sure safety spring 

5

 is mounted. 

Risk of injury when machine is tilted back.

SAFETY PRECAUTIONS

! 

The eye protection 

6

 can be ordered optionally, but must not be removed after 

installation without consultation with the operator.

 

The finger guard 

7

 must not be removed!

Summary of Contents for 5000




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands