background image

 0

2

/

25

/0

5

 

34

-126-12

0

.doc 

V

ESTIL 

M

FG

.

 

C

O

./T&S

 

E

QPT

.

 

C

O

.  

1 of 1 

O

NE

-

YEAR 

P

RODUCT 

W

ARRANTY

 

 
 
ONE YEAR LIMITED WARRANTY 

For the original purchaser, the manufacturer warrants against defects in materials and workmanship that develop 

during normal service and proper use for a period of one year after the date of shipment (not to exceed 15 months 
after date of manufacture). 

Any part that is determined by the manufacturer to be defective in material or workmanship will be, as the exclusive 
remedy, repaired or replaced at the manufacturer’s option.   

Any items returned to the factory must be pre-authorized with a return authorization number and have shipping costs 

prepaid.  (All non-warranty returns are subject to a minimum 20% restocking fee.) 

Labor costs for warranty repairs and/or modifications are not covered unless done at the manufacturer’s facilities or 

pre-approved by the manufacturer.  Any modifications or repairs performed without prior written approval of the 
manufacturer can void the warranty.   

Warranty claims must be made in writing within said year. 

This limited warranty gives the purchaser specific legal rights which vary from state to state. 

LIMITATION OF LIABILITY 

To the extent allowable under applicable law, the manufacturer’s liability for consequential and incidental damages is 
expressly disclaimed.  The manufacturer’s liability in any event is limited to, and shall not exceed, the purchase price 

paid.  Misuse will, and modification might, void the product’s warranty. 

This warranty does not apply to claims made due to unauthorized repairs or alterations, freight damage, negligence, 

accidents, abuse, misuse, or misapplication of the equipment. 

This warranty does not cover costs of labor or consequential damages including, but not limited to: business 

interruption costs; lost profits, or; lost business opportunities. 

Warranty shall not be honored for equipment having past-due invoices. 

WARRANTY DISCLAIMER 

The manufacturer has made a diligent effort to accurately illustrate and describe their products.  However, such 
illustrations and descriptions are for the sole purpose of identification, and do not express, imply, or warrant that a 

given product is merchantable or fit for a particular purpose, or that the product will necessarily conform to the 
illustrations or descriptions.  All product specifications are subject to change without notice. 

DISPOSITION 

The manufacturer will make a good faith effort to effect prompt correction or other adjustment with respect to any 
product that proves to be defective within the Limited Warranty Period.  

 

The provisions of the warranty shall be construed and enforced in accordance with the Uniform Commercial Code and 
laws as enacted in the State of Indiana. 

 

Summary of Contents for JMD-1000












Reviews: