background image

Table of Contents

  

12/2/20 

FM MANUAL.DOCX 

Table of Contents

  

Copyright 2020, Vestil Manufacturing Corp. 

Page 20 of 20 

LIMITED WARRANTY 

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship 

during the warranty period. Our warranty obligation is to provide a replacement for a defective, original part covered by the 
warranty after we receive a proper request from the Warrantee (you) for warranty service. 
Who may request service? 

Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an 

authorized distributor AND Vestil has been fully paid. 
Definition of “original part”? 

An original part is a part used to make the product as shipped to the Warrantee. 

What is a “proper request”? 

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the 

shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests by 
one of the following methods: 
US Mail 
Vestil Manufacturing Corporation 
2999 North Wayne Street, PO Box 507 
Angola, IN 46703 

Fax 

(260) 665-1339 

Phone 

(260) 665-7586 

Email 

[email protected]

 

Enter “Warranty service request” in subject field 

In the written request, list the parts believed to be defective and include the address where replacements should be 

delivered. After Vestil receives your request for warranty service, an authorized representative will contact you to 
determine whether your claim is covered by the warranty. Before providing warranty service, Vestil will require you to send 
the entire product, or just the defective part (or parts), to its facility in Angola, IN. 
What is covered under the warranty? 

The warranty covers defects in the following original, dynamic parts: motors, hydraulic pumps, motor controllers, and 

cylinders. It also covers defects in original parts that wear under normal usage conditions (“wearing parts”), such as 
bearings, hoses, wheels, seals, brushes, and batteries. 
How long is the warranty period? 

The warranty period for original dynamic components is 1 year. For wearing parts, the warranty period is 90 days. 

Both warranty periods begin on the date Vestil ships the product to the Warrantee. If the product was purchased from an 
authorized distributor, the periods begin when the distributor ships the product. Vestil may, at its sole discretion, extend a 
warranty period for products shipped from authorized distributors by up to 30 days to account for shipping time. 
If a defective part is covered by the warranty, what will Vestil do to correct the problem? 

Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact 

you to discuss your claim. 
What is not covered by the warranty? 

The Warrantee (you) are responsible for paying labor costs and freight costs to return the product to Vestil for 

warranty service. 
Events that automatically void this Limited Warranty. 

 

Misuse; 

 

Negligent assembly, installation, operation or repair; 

 

Installation/use in corrosive environments; 

 

Inadequate or improper maintenance; 

 

Damage sustained during shipping; 

 

Collisions or other accidents that damage the product; 

 

Unauthorized modifications: Do not modify the product IN ANY WAY without first receiving written authorization from 
Vestil. 

Do any other warranties apply to the product? 

Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent 

allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty. Vestil makes 
no warranty or representation that this product complies with any state or local design, performance, or safety code or 
standard. Noncompliance with any such code or standard is not a defect in material or workmanship. 

 

 

Summary of Contents for FM-0648





















Reviews: