VESTEL TRV 50 Service Manual Download

Page: 28 / 28

VESTEL WATER HEATER SERVICE MANUAL

VESTEL BEYAZ EŞYA A.Ş. (Air Conditioning Quality Assurance Department)

Page

MALFUNCTION

CAUSE OF MALFUNCTION

TROUBLESHOOTING

Water heater is making noise
during heating.

* Heating coil may be covered
with scale.

* It may be the boiling sound of
water while heating coil is
heating.

* Clean heating coil.

* It is a normal process. There is no
need for further actions.

There is water leak in heating
coil and flange unit

* Flange or heating coil gaskets
may be damaged.

* Corrosion may have caused
puncture in flange.

* Replace gaskets.

* Replace flange and gaskets (mount
the flange carefully in both cases).

NOTE: Temperature control is electronic in certain models of water heaters. For this reason, thermostat used for
heat control is digital. It detects heat through a sensor.

Summary of Contents for TRV 50





























Search results

Summary of Contents for TRV 50

Reviews:

Related manuals for TRV 50

Brands by name

Popular brands

VESTEL TRV 50, Service Manual

Search results

Summary of Contents for TRV 50

Reviews:

Related manuals for TRV 50

Brands by name

Popular brands