3
8
11
12
2
1
4
5
6
7
9
10
14
15
16
17
18
19
20
21
22
23
24
25
26
-6-
-7-
MIC SECTION
MASTER SECTION
PROGRAM INPUT SECTION
q
INPUT SELECTOR
Used to select input (2 line or 1 phono) to be sent
to each PGM channel.
w
PGM TRIM
This control is used to adjust the input level
volume for the best possible sound.
When making adjustments to the "TRIM" of an
input, try and ensure that the signals level only
occassionlly goes in to the "RED" range.
e
OVERLAOD INDICATOR
Lights in red when input level is over
r
PGM BALANCE
Adjusts the stereo balance for each PGM
channel. Can be used for adjusting the
unbalanced stereo image. Clockwise rotation from
center position increases the volume of R over L
channel. A counter clockwise rotation increases
the volume of L channel over R.
t
PGM ISOLATOR
【
HI
】
Adjusts the HI frequency level of each PGM
channel.
y
PGM ISOLATOR
【
MID
】
Adjusts the MID frequency level of each PGM
channel.
u
PGM ISOLATOR
【
LOW
】
Adjusts the LOW frequency level for each PGM
channel.
i
ISOLATOR ON/OFF SWITCH
When set to "OFF", a normal signal is
transmitted regardless of the position of any
isolator controls.
o
AUX ASSIGN SWITCH
This switch enables the signal from each
program to be sent to AUX send jack. Different
signal routes can be selected this switch to
different positions.
PRE : The signal before the input fader (after
the EQ) will be sent to AUX output.
POST: The signal after the input and crossfader
will be sent to AUX output.
OFF : No signal will be sent to AUX output.
!0
AUX SEND LEVEL
Used to adjust the output level from AUX SEND
JACK. This signal is selected by the effect
switch.
!1
Used to send the signal from each program to
the monitor section for headphone monitoring.
!2
INPUT FADER
Used to adjust the Input level of each program.
Usually set to 7-8 positions. This is a detachable
fader for ease of replacement, replace with IF-
180 when it is worn out. If you wish to use the
fader unit with slide stroke distance of 45mm,
you can replace with the Vestax "IF-37PCV".
See "HOW TO CHANGE THE FADER UNIT".
!3
CROSS FADER
When the input level of PGM1 and PGM2 are
properly set, PGM1 will be heard with the
crossfader set to the left side. PGM2 will be
heard with the cross fader set to the right side.
When the crossfader is set in the center, both
programs will be heard. This is detachable fader
for the ease of replacement with "CF-PCV" or
"CF-R" when it is worn out.
CUE ON/OFF SWITCH
!4
MAIN MIC IN JACK [1/4" PHONE JACK]
Input jack for MAIN MIC.
!5
SUB MIC IN JACK [1/4" PHONE JACK]
Input jack for SUB MIC.
!6
MAIN MIC LEVE
Adjusts the input level of the MAIN MIC input.
!7
MAIN MIC EQ
【
HI , LOW
】
Adjusts the HI and LOW frequencies for both the
MAIN and SUB MIC input.
!8
MAIN MIC AUX ON/OFF SWITCH
Used to send the signal to the external effect
processor connected to the AUX SEND.
!9
MAIN MIC CUE ON/OFF SWITCH
Used to send the signal from the mic channel to
the monitor section for headphone monitoring.
@0
MASTER LEVEL
Adjusts the signal level of
the master output.
@1
MASTER BALANCE
Adjusts the signal balance
between left and right of
the master output.
@2
SUB MASTER LEVEL
Adjusts the signal level
outputs
from
SUB
MASTER OUTPUT JACK
on the rear panel.
@3
AUX RECEIVE LEVEL
Adjusts the output level
from AUX RCV JACK.
@4
AUX RECEIVE CUE ON/OFF SW
Used to send the effect
receive signal to the
monitor section for the
headphone monitoring.
@5
MONITOR STYLE SELECT SWITCH
When this switch is set to
"SPLIT", the master signal
is always heard through
the right ear-cup of the
headphones. The signal
selected by MONITOR
SELECT SWITCH will be heard in the left ear-
cup. This enables both programs to be
monitored simultaneously, thus assisting in
beat mixing. When this switch is set to
"STEREO", no master output is heard in the
headphones, and only the signal selected by
MONITOR SELECT SWITCH will be heard in
both ear-cups.
@6
MONITOR LEVEL
Adjusts the headphone monitor level.
@7
HEADPHONE JACK
Connect the headphones with the impedance
of 8ohm to 600 ohm.
@8
LED LEVEL METER
The LED bar level meters indicate the L and R
outputs.
@9
POWER INDICATOR
Lights up when the POWER SWITCH is on.
VMC-180E 04.10.8 7:04 PM ページ 7
