Vestax VMC-180, Owner'S Manual, Page: 6 / 6

fig.e
fig.f
fig.g
:for "CF-PCV"
:for "CF-R"
TURNTABLE［VESTAX PDX-2000MK II ］
TURNTABLE［VESTAX PDX-2000MK II ］ CD PLAYER［VESTAX CDX-16］ TURNTABLE［VESTAX PDX-2000MK II ］ CD PLAYER［VESTAX CDX-16］
TAPE RECORDER CD, MD, DAT, etc.
EFFECTOR ［ DELAY, REVERB, SAMPLER ］
POWER AMPLIFIER［VESTAX DA-X1000］
OUT PUT
CD, MD, Player, TAPE DECK, etc. CD, MD, Player, TAPE DECK, etc.
PLAY/PAUSE CUE PLAY/PAUSE CUE
KEY PITCH
REVERSE
OPEN/ CLOSE
STOP
DISPLAY
REPEAT
A B
SEARCH
TRACK MIN SEC FRM
LOCATE
ENTER 1 2 3
LOOP
START END RELOOP/EXIT
POINT FOCUS
MONITOR
LINE1
or
LINE2
LINE4
or
LINE5
PHONO1
PHONO3
GND
GND
PLAY/PAUSE CUE PLAY/PAUSE CUE
KEY PITCH
REVERSE
OPEN/
CLOSE
STOP
DISPLAY
REPEAT
A B
SEARCH
TRACK MIN SEC FRM
LOCATE
ENTER 1 2 3
LOOP
START END RELOOP/EXIT
POINT FOCUS
MONITOR
PHONO2 LINE3
AUX
SEND
AUX
RCV
IN OUT
MASTER
MAIN SPEAKER
［VESTAX VLS-10］
MAIN SPEAKER
［VESTAX VLS-10］
GROUND LEAD
GND
GROUND LEAD
CD, MD, Player, TAPE DECK, etc.
CD PLAYER［VESTAX CDX-16］
/ / / / /
MIC MIC
REC OUT REC OUT
LINE 1 LINE 1
CD- CD-
R/R R/RW 1 W 1
MIC/A MIC/AUX IN UX IN
MASTER 1
GROUND LEAD
-10- -11-
CONNECTION
■change to "CF-PCV"
①Remove the fader knobs. (see fig-a)
②Remove the bottom cover. (see fig-b)
③Remove the 2 screws which fix the crossfader unit, and
remove the fader unit from position in mixer. (see fig-c)
④Carefully remove the multi-cable connector from the
fader unit. (see fig-d)
⑤ Remove the screws which fix the crossfader volume.
(see fig-e)
⑥ Remove the knob and the panel of new a new fader unit
"CF-PCV". (refer to fig-f)
⑦Secure the CF-PCV without panel and knob using
original screws. Only 2 screws are used to secure the
CF-PCV. (see fig-g)
⑧Attach multi-cable connector to new fader unit.
⑨Position the fader unit carefully and secure with screws.
■change to "CF-R"
①Remove the objective crossfader in the same procedure
as above ①〜⑤.
②Remove the knob and the panel of a new fader unit "CF-
R". (see fig-f)
③Secure the CF-R without panel and knob using original
screws. Only 2 screws are used to secure the CF-R.
(see fig-g)
④Attach multi-cable connector to new fader unit.
⑤ Position the fader unit carefully and secure with screws.
HOW TO CHANGE THE CROSS FADER UNIT
Note
Set switch to "PCV" position.
PGM2 PGM1
SUB
VMC-180E 04.10.8 7:04 PM ページ 11