Vesper WMX850 User Manual Download Page 59 | Manualshive

Page: 59 / 63

background image

- 59 -

Examining Received NMEA Data

As a troubleshooting aid it is possible to have the

AIS

WatchMate

display the raw sentence

data received on its NMEA input port. This can help you to resolve wiring and other
installation problems. When using this mode, normal operation is not performed. Only the
raw data display is done.

To view the raw sentence data received on the NMEA port, press and hold the 2nd button
from the top while turning the unit on by pressing the power button. Once the unit has come
on and displayed the message “Data Received from NMEA Port”, you can release the top
button.

All data received on the port will be displayed as it arrives. When the display fills it will be
erased and data will again be displayed from the top. You can freeze the display by pressing
and holding any button. To resume the display, release the button.

To return to normal operation, turn the unit off and back on again.

«
...
57
58
59
60
61
...
»

Summary of Contents for WMX850
































































Reviews:

No comments

Related manuals for WMX850

Brand: Eaton Pages: 22

Brand: Jensen Pages: 12

hsb2 PLUS Series

Brand: Raymarine Pages: 2

Brand: SimonsVoss Pages: 16

Brand: Timex Pages: 8

Brand: König Electronic Pages: 21

Brand: Denver Pages: 59

Brand: Cobra Pages: 24

Chronomatic-278

Brand: Radio Shack Pages: 14

Brand: MAJORITY Pages: 112

Brand: Vertex Standard Pages: 10

Brand: Craig Pages: 9

Brand: Garmin Pages: 59

Simrad NISE 3900E

Brand: Kongsberg Pages: 50

Alphatron Marine Rudder Feedback Unit HD

Brand: JRC Pages: 34

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 8

Brand: Sanyo Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands