10
•
When operating the table saw keep your body in firm position.
•
All parts of the table saw must be properly fixed.
•
Do not make profile or penetrating cuts with the table saw.
•
When carrying the table saw, hold only by transport handles, do not
hold by saw shields.
•
During transportation upper part of the cutting blade must be
covered with the shield.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always
a small risk of operational injuries.
CONSTRUCTION AND USE
Table saw is designed for cutting wood and wood-like materials. Do
not use the saw for cutting firewood. Attempts to use the table saw
for purposes other than specified will be considered an improper use.
Use the table saw only with appropriate cutting blades with teeth
with solid carbide inserts. Range of use covers repair and building
works, and any work from the range of individual, amateur activities
(tinkering).
Use the tool according to its purpose only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1.
Angle bar
2.
Rip fence
3.
Cutting blade shield
4.
Fixing knob for cutting blade shield
5.
Work table
6.
Locking knob for cutting blade tilt
7.
Switch
8.
Fixing knob for rip fence
9.
Dust extraction outlet
10.
Cover
11.
Riving knife
12.
Cutting blade
13.
Work table insert
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Rip fence
- 1 pce
2
. Screw + washer
-
2
sets
3
. Angle bar
- 1 pce
4
. Push stick
- 1 pce
5
. Ring
spanner
-
2
pcs
PREPARATION FOR OPERATION
SAW INSTALLATION ON A WORKSHOP BENCH
It is recommended to firmly fix the table saw to a workbench with the
use of mount holes designed for such purpose. They are located on
the table saw base and guarantee safe operation and eliminate risk of
unwanted machine shifts during operation.
Make sure the package
is removed from underneath of the motor.
INSTALLATION OF CUTTING BLADE SHIELD
•
Put cutting blade shield (
3
) on the riving knife (
11
).
•
Put the fixing knob fro cutting blade shield (
4
) into hole in the cutting
blade shield (
3
) and the riving knife (
11
) and tighten the knob.
•
You can remove the cutting blade shield following above procedure
in reverse sequence.
Knob for locking the cutting blade shield should be tightened, so the
cutting blade shield lifts as the material is fed towards the cutting
blade and returns to default position after the cutting is finished.
DUST EXTRACTION
Table saw is equipped with dust extraction outlet (
9
) which allows
sucking off sawdust emerging while cutting. Use appropriate vacuum
suction devices or industrial vacuum cleaners for this purpose.
INSTALLATION OF RIP FENCE (HEIGHT OF REACTION)
Rip fence can be installed on either side of the work table.
•
Install fixing knobs for rip fence (
8
) and washer for the rip fence (
2
).
•
Slide the rip fence (
2
) into slot in the work table (
5
).
•
Set required cutting width using scales located on the work table top (
5
).
•
Tighten fixing knobs for the rip fence (
8
).
The rip fence (
2
) has two guiding surfaces (upper and lower setting
edge). Depending on thickness of the material to cut, install the rip
fence properly (
fig. A
).
•
Loosen the fixing knobs for rip fence (
8
) and slide the rip fence (
2
)
out of the slots in the work table (
5
).
•
Turn over the rip fence (
5
) by 1
8
0
0
and attach it back to the work table (
5
).
SETTING THE RIVING KNIFE
Disconnect the tool from power supply.
•
Remove the cutting blade shield (
3
) and the work table insert (
13
)
by undoing the fixing screws.
•
Loosen screws (
a
) fixing the riving knife (
11
) (
fig. B
).
•
Set the riving knife (
11
) so the distance from the cutting blade (
12
)
is between
3
–
5
mm (riving knife should be exactly in line with the
cutting blade) (
fig. C
).
•
Tighten screws for riving knife locking (
a
), install table top insert
(
13
) and cutting blade shield (
3
).
Check position of the riving knife after each replacement of the
cutting blade.
OPERATION / SETTINGS
Ensure the table saw is disconnected from power supply network
before starting any adjustments. To ensure safe, precise and
efficient table saw operation, proceed with all adjustment
procedures as a whole.
After finishing all the setting and adjustment procedures
ensure that all adjustment keys are collected. Check that all
threaded joining elements are properly tightened. When making
adjustments ensure that all external parts work properly and are in
good condition. Any worn out or damaged part must be replaced
by qualified personnel before starting to use the table saw.
Summary of Contents for 52G219
