Vertiv Avocent ACS800 Installer/User Manual Download Page 52

Page: 52 / 100

PARAMETER

DESCRIPTION

Status

Enables or disables the port. Default: Disabled.

Phone No.

The phone number to dial to.

Speed

The speed that will be used to configure the serial device and communicate with the connected modem.

Init Chat

Chat for modem initialization.

Local IPv4/IPv6 Address

Configures the local IPv4/IPv6 address for this PPP connection. If empty, PPP will accept the address from the remote peer.

Remote IPv4/IPv6 Address

Configures the remote IPv4/IPv6 address for this PPP connection. If empty, PPP will accept the address from the remote
peer.

PPP Authentication
Protocol

PPP Idle Timeout

Number of seconds being idle before PPP times out. Default: 0 (no time-out).

CHAP

Table 3.17 Dial-out Parameters

Socket client profile

To configure the socket client profile for a serial port with a connected device:

Select

Ports - Serial Ports

Click the checkbox for a serial port with a connected device.

Click

Set Socket Client

and use the drop-down menus to configure the physical settings.

4. Configure the Socket Client Settings (remote server address, TCP port and event trigger) and click

Save

PARAMETER

DESCRIPTION

RJ-45 Pin-Out

Defines the serial port pinout.

Status

Defines the status of the serial port as either enabled or disabled. Default: Disabled.

Speed

Defines the speed as 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 or 230400. Default: 9600.

Parity

Defines the parity as Even, Odd or None. Default: None.

Data Bits

Defines the data bits as 5, 6, 7 or 8. Default: 8.

Stop Bits

Defines the stop bits as 1 or 2. Default: 1.

Flow Control

Defines the flow control as none, hardware, software, RxON software or TxON software. Default: None.

Remote Server

IPv4 or IPv6 address of the remote server.

Remote TCP Port

TCP port to be used to establish a connection with a remote server.

Establish Connection

Configure the event that will trigger the establishment of the connection: DCD Regards or Always.

Table 3.18 Socket Client Parameters

3.3.8 Pluggable devices

The console server supports a variety of pluggable devices connected to its USB ports. Some models also support a single
SD card in the SD card slot.

Vertiv™ | Avocent® ACS800/8000 Advanced Console Server Installer/User Guide

Summary of Contents for Avocent ACS800





































































































Search results

Summary of Contents for Avocent ACS800

Reviews:

Related manuals for Avocent ACS800

Brands by name

Popular brands

Vertiv Avocent ACS800, Installer/User Manual

Search results

Summary of Contents for Avocent ACS800

Reviews:

Related manuals for Avocent ACS800

Brands by name

Popular brands