manualshive.com logo in svg

Vertical Technologies DeltaQuad Evo, Operation Manual

Share
Download
Vertical Technologies DeltaQuad Evo Operation Manual Download Page 64

When replacing propellers for the VTOL modules no lock bond is required as these are self-tightening. 
When replacing the pusher motor propeller lock bond is required on the propeller adapter nut as this motor 
can spin in both directions.

Scheduled maintenance

The recommended service cycle for the DeltaQuad UAV  12 months. Beyond this point the vehicle can fly 
less efficient and there could be a potential risk of failure. Using the Vertical Technologies 

 you can extend the lifetime of your vehicle and maintain warranty on the serviced 

components.

Extended 

Maintenance Service

Vehicles flown beyond the recommended maintenance cycles void their warranty.

Extended Maintenance Service

With the Extended Maintenance Service you can send back your vehicle and we will completely refurbish it. 
It will be returned as good as new. If the vehicle was damaged beyond repair it can be completely replaced. 
We offer this service free of any obligation and for a fixed fee. All replaced components are provided with a 
new warranty.

There are 3 types of extended maintenance requests:

Custom repair

Basic tuneup

Complete refresh

Software upgrade

✔

✔

✔

Recalibration of 
sensors

✔

✔

✔

Full inspection and test 
flight

✔

✔

✔

New propellers

 

✔

✔

New motors

 

✔

✔

New speed controllers

 

✔

✔

New BECs

 

✔

✔

New servos

 

✔

✔

New connectors

 

 

✔

New board computers

 

 

✔

New GPS

 

 

✔

New power module

 

 

✔

Summary of Contents for DeltaQuad Evo































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands